Light Fixture For Ceiling Fan – The flush-style ceiling fan is mounted snugly alongside a flat horizontal fairly low ceiling where it is off the beaten track, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, according to the size of the room being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the equipment and possible other parts essential for installing them, their self-assemble kits have any devices. In many cases, the fan, that may have its own lighting, will replace a ceiling fitting.
Safety, The electricity has to be off at the site the place that the fan shall be installed. If the fan is replacing a fitting, power down its fuse or circuit breaker together with flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; do not lean or get into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, as appropriate
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the fitting from the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws from the electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to the fixture are cold (the test light will remain off). Cut the wires, leaving 3-5″ of tail allowing you to connect the crooks to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one along with a white one. Tip: also look at the firmness from the electrical box in the ceiling. If it is not solidly attached to the ceiling, add two extra screws to its top side, which could require drilling two holes in the box for the children. The ceiling fan is heavier as opposed to fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires in the junction box cleanly, install the mounting bracket on the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger to the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor along with a blue or off-color one for your lights to become attached below it. Overlap the stripped ends of those two wires (motor and lights) together with all the stripped end from the black ceiling wire in the box, and twist connect them together with all the wire nut provided. Connect the white assembly wire on the white ceiling wire exactly the same.
Then, to help keep these connections from loosening even though the fan is working, tape the wide lower ends of those nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) on the electrical box in the event the box can also be grounded having a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask an experienced relating to this green wire connection. Some will say to let it sit be, i.e., do nothing at all with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends from the mounting bracket with all the small screws provided. It covers/hides the perimeters from the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets with all the screws and washers provided. Then mount the blades on the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to help keep them separate from the rest from the kit hardware.
Tip: to help keep the motor from becoming too off-level within this step, install the blades one-by-one opposite to each other to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just under the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided in the event the lighting assembly is not wanted without any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on with all the wall switch, even though the fan itself is controlled from the pull-chain switch only, initially set in the off position. Note: The ceiling fan includes a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.