Clarkston 44 In Indoor Brushed Nickel Ceiling Fan With Light Kit regarding size 1000 X 100044 Inch Ceiling Fan With Light – The flush-style ceiling fan is mounted snugly next to a designated horizontal fairly low ceiling where it really is dealt with, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of room being fitted, and can cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the various tools and possible other regions required for installing them, their self-assemble kits have anything else. In many cases, the fan, that can have a unique lighting, will replace a ceiling light fixture.
Safety, The electricity must be off to begin where the fan will be installed. If the fan is replacing a light fixture, shut down its fuse or circuit breaker as well as flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; usually do not lean or enter into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if required
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the light fixture from the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws from the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections for this fixture are cold (quality light will continue to be off). Cut the wires, leaving 3-5″ of tail to get in touch them to the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one and a white one. Tip: also confirm the firmness of the electrical box within the ceiling. If it really is not solidly coupled to the ceiling, add two extra screws to its top side, which can require drilling two holes within the box on their behalf. The ceiling fan is heavier as opposed to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires within the junction box cleanly, install the mounting bracket to the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger in to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor and a blue or off-color one for the lights to be attached below it. Overlap the stripped ends of these two wires (motor and lights) together using the stripped end of the black ceiling wire within the box, and twist connect them together using the wire nut provided. Connect the white assembly wire to the white ceiling wire exactly the same.
Then, to help keep these connections from loosening as the fan is working, tape the wide lower ends of these nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) to the electrical box if your box is additionally grounded having a third bare or green wire. Otherwise, if your electrical box in not grounded, ask an experienced concerning this green wire connection. Some will say to let it sit be, i.e., relax with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends of the mounting bracket using the small screws provided. It covers/hides the edges of the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets using the screws and washers provided. Then mount the blades to the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to help keep them separate from the rest of the kit hardware.
Tip: to help keep the motor from becoming too off-level with this step, install the blades one at a time opposite to each other in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just under the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided if your lighting assembly is not wanted without any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on using the wall switch, as the fan itself is controlled from the pull-chain switch only, initially set within the off position. Note: The ceiling fan has a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.
