Basement Ceiling Fan

Posted on

Basement Drop Ceiling Ideas Fan Basement Drop Ceiling Ideas with sizing 1024 X 768Basement Drop Ceiling Ideas Fan Basement Drop Ceiling Ideas with sizing 1024 X 768


Basement Ceiling Fan – The flush-style ceiling fan is mounted snugly alongside a set horizontal fairly low ceiling where it can be off the beaten track, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, depending on the size of the room being fitted, and can cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the equipment and possible other parts required for installing them, their self-assemble kits have everything else. In many cases, the fan, that will have its lighting, will replace a ceiling permanent fixture.

Safety, The electricity have to be off once your there the location where the fan shall be installed. If the fan is replacing a permanent fixture, de-activate its fuse or circuit breaker along with flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; tend not to lean or enter into a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, as appropriate

Installation steps (reading the fan installation instructions thoroughly). 1. Remove the permanent fixture through the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws through the electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to this particular fixture are cold (quality light will remain off). Cut the wires, leaving 3-5″ of tail for connecting these to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one and a white one. Tip: also check the firmness in the electrical box in the ceiling. If it can be not solidly attached to the ceiling, add two extra screws to its top side, which could require drilling two holes in the box for the kids. The ceiling fan is heavier than the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires in the junction box cleanly, install the mounting bracket for the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger into the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor and a blue or off-color one for your lights to become attached below it. Overlap the stripped ends of these two wires (motor and lights) together using the stripped end in the black ceiling wire in the box, and twist connect them together using the wire nut provided. Connect the white assembly wire for the white ceiling wire exactly the same way.


Then, to maintain these connections from loosening while the fan is working, tape the wide lower ends of these nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) for the electrical box when the box is also grounded using a third bare or green wire. Otherwise, when the electrical box in not grounded, ask a professional about it green wire connection. Some will say to get forced out be, i.e., do nothing at all from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends in the mounting bracket using the small screws provided. It covers/hides the perimeters in the motor along with the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets using the screws and washers provided. Then mount the blades for the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to maintain them separate through the rest in the kit hardware.

Tip: to maintain the motor from becoming too off-level in this step, install the blades one-by-one opposite to one another to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just below the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided when the lighting assembly is just not wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on using the wall switch, while the fan itself is controlled by the pull-chain switch only, initially set in the off position. Note: The ceiling fan includes a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.