Ceiling Fans Without Blades – The flush-style ceiling fan is mounted snugly alongside a flat horizontal fairly low ceiling where it can be out of the way, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of room being fitted, and can cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the instruments and possible other areas required for installing them, their self-assemble kits have anything else. In many cases, the fan, which will have a unique lighting, will replace a ceiling permanent fixture.
Safety, The electricity must be off to begin the location where the fan shall be installed. If the fan is replacing a permanent fixture, shut down its fuse or circuit breaker together with flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder through the installation; usually do not lean or enter a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if required
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the permanent fixture from your ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws from your electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to this particular fixture are cold (the test light will continue to be off). Cut the wires, leaving 3-5″ of tail allowing you to connect the crooks to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one along with a white one. Tip: also look into the firmness with the electrical box within the ceiling. If it can be not solidly connected to the ceiling, add two extra screws to its top side, which might require drilling two holes within the box for the kids. The ceiling fan is heavier compared to the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires within the junction box cleanly, install the mounting bracket for the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in to the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor along with a blue or off-color one for that lights to get attached below it. Overlap the stripped ends of the two wires (motor and lights) together using the stripped end with the black ceiling wire within the box, and twist connect them together using the wire nut provided. Connect the white assembly wire for the white ceiling wire exactly the same.
Then, to maintain these connections from loosening as the fan is working, tape the wide lower ends of the nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) for the electrical box if the box is additionally grounded which has a third bare or green wire. Otherwise, if the electrical box in not grounded, ask a specialist about this green wire connection. Some will say to leave it be, i.e., do nothing by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends with the mounting bracket using the small screws provided. It covers/hides the sides with the motor and the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets using the screws and washers provided. Then mount the blades for the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to maintain them separate from your rest with the kit hardware.
Tip: to maintain the motor from becoming too off-level in this step, install the blades one-by-one opposite to one another to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just below the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided if the lighting assembly just isn’t wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on using the wall switch, as the fan itself is controlled with the pull-chain switch only, initially set within the off position. Note: The ceiling fan includes a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.