Westinghouse Antique Brass Replacement Fan Blade Arms 5 Pack pertaining to proportions 1000 X 1000Ceiling Fan Blade Arms – The flush-style ceiling fan is mounted snugly close to a flat horizontal fairly low ceiling where it is taken care of, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the tools and possible other parts needed for installing them, their self-assemble kits include any devices. In many cases, the fan, that can have its lighting, will replace a ceiling light fixture.
Safety, The electricity should be off at the site where the fan will be installed. If the fan is replacing a light fixture, de-activate its fuse or circuit breaker in addition to flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; tend not to lean or enter a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, as appropriate
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the light fixture through the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws through the electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections for this fixture are cold (the test light will remain off). Cut the wires, leaving 3-5″ of tail in order to connect these phones the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one along with a white one. Tip: also look at the firmness of the electrical box inside the ceiling. If it is not solidly attached to the ceiling, add two extra screws to its top side, that might require drilling two holes inside the box on their behalf. The ceiling fan is heavier compared to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires inside the junction box cleanly, install the mounting bracket for the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor along with a blue or off-color one for your lights to get attached below it. Overlap the stripped ends of such two wires (motor and lights) together using the stripped end of the black ceiling wire inside the box, and twist connect them together using the wire nut provided. Connect the white assembly wire for the white ceiling wire much the same way.
Then, to maintain these connections from loosening while the fan is working, tape the wide lower ends of such nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) for the electrical box when the box is also grounded using a third bare or green wire. Otherwise, when the electrical box in not grounded, ask a professional relating to this green wire connection. Some will say to let it rest be, i.e., do nothing at all from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends of the mounting bracket using the small screws provided. It covers/hides the edges of the motor along with the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets using the screws and washers provided. Then mount the blades for the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to maintain them separate through the rest of the kit hardware.
Tip: to maintain the motor from becoming too off-level during this step, install the blades one-by-one opposite to one another to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just underneath the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided when the lighting assembly just isn’t wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on using the wall switch, while the fan itself is controlled by the pull-chain switch only, initially set inside the off position. Note: The ceiling fan features a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.
