Ceiling Fans For Cathedral Ceilings – Two good reasons to install a ceiling fan, cooling and heating. If you live in the cold climate, fans can push warm air gathered at the ceiling down again. Ceiling fans can be an easy task to install in case you have some mechanical aptitude. Current ceiling fans include remote-controls to vary speed and adjust lighting. If your room already has a permanent fixture in the ceiling, your permanent fixture probably has one hot or feed wire likely to it, the neutral white along with the bonding green or copper. Essentially this is a three-wire system. Many new construction homes have four wires available, one for your light and something for your fan motor control along with the neutral and ground. If you have only one Hot wire feeding the ceiling junction box, the remote-control fans work along with your application. Additionally some remote-controlled fans use wall controller which sends its signal for the fan just like a TV remote. It just seems like a wall control unit. If you just have the electricity wire for your remote-controlled fan, please cap off of the fourth wire which you will n’t need to make use of. This should be shown in your directions that was included with the fan assembly.
Once you might have acquired a fan you want, assemble it according for the instructions given. Some fans are a much more complex, ask a friend to aid if need be. It is best to help it become assembled correctly, creating a ceiling fan blade thud yourself on your head can be annoying. Once you might have the pre-assembly completed, anyone can prepare the ceiling junction box. Of course I know you might have already made sure the electricity for the ceiling box is switched off and no one can energize it accidentally. Once you might have succeeded in doing so, you must find three wires in the J-box. A copper or green wire for bonding. A white wire for your neutral and a red or black wire for your power. If your junction box has a fourth wire, this could be setup for a wall controlled fan switch which can be great and allows you to make use of a non-remote wall controller. I should mention that some all fans include a wall controllers designed as remotes so don’t be confused as these all help the singular feed in your ceiling junction box.
A word about weight, not yours but a word about the sized your fan. If you might have a substantial fan and its weighted near 12 pounds or higher, you may need a special junction box that may secure the additional weight. I would recommend you ask someone that knows about these heavier fans if that is what you will be likely to install. Most fans are lighter and can be set up in most junction boxes without modifications.
Now we should get it there, the fan which is. Many fans include a Hanger shaped like a U. Install this hanger on to your box, the screws should be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you might have the hanger installed, pick-up your fan motor devoid of the blades installed and it on the hanger. This allows you the electrician to attach the wires without struggling to juggle the motor and wire it as well. Connect the bonding wire for the chassis as noted in the instructions. Next connect the white neutral wire, and now the black wire. Swing the fan into place using the parts provided. Some have brackets, some utilize a metal plate while others use preformed mounting bases. Use your instructions and you will have a fan quickly. Smaller fans may need one to pre-assemble your blades before hanging the fan. I always found installing the motor first and after that installing the blades last is easier. It does require however, one to work above your mind to have the blades attached.
Once you might have the fan hanging, the blades installed and everything tightened anyone can step off of the ladder, relax, then install the wall controller as provided. These all vary in design nevertheless they all follow similar procedures. Remember, you will find a line and load situation here. This means, the line side may be the list of wires the feed in the switch box through the panel whilst the Load side is likely to your fan. This is critical so be sure you comprehend the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next perform Line (incoming) side next: Bond or ground should already be made up for the new controller. Next wire your white neutral for the controllers neutral for your Line side. You may have already wired your neutrals together according to your instructions. Now wire your Hot or Power wire for the Line side of your respective controller. If you might have the fourth wire within, cap it off or use it for your motor control and connect it accordingly for your directions. Red to Red is often the case here. Once completed, be some Iced Tea and luxuriate in your fan.