Hampton Bay Universal Ceiling Fan Wireless Wall Switch 68109 The with size 1000 X 1000Ceiling Fan Control – The flush-style ceiling fan is mounted snugly beside a designated horizontal fairly low ceiling where it really is off the beaten track, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of the room being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the tools and possible other regions essential for installing them, their self-assemble kits come with any devices. In many cases, the fan, that can have its own lighting, will replace a ceiling fitting.
Safety, The electricity have to be off to begin where the fan is usually to be installed. If the fan is replacing a fitting, power down its fuse or circuit breaker together with flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder through the installation; usually do not lean or enter into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is required, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if necessary
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the fitting from the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws from the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections for this fixture are cold (quality light will continue to be off). Cut the wires, leaving 3-5″ of tail allowing you to connect the crooks to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one along with a white one. Tip: also check the firmness with the electrical box inside ceiling. If it really is not solidly attached to the ceiling, add two extra screws to its top side, which might require drilling two holes inside box for them. The ceiling fan is heavier as opposed to fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires inside junction box cleanly, install the mounting bracket for the box with the two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger to the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor along with a blue or off-color one for the lights to be attached below it. Overlap the stripped ends of these two wires (motor and lights) together with the stripped end with the black ceiling wire inside box, and twist connect them together with the wire nut provided. Connect the white assembly wire for the white ceiling wire exactly the same.
Then, to help keep these connections from loosening even though the fan is working, tape the wide lower ends of these nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) for the electrical box in the event the box is additionally grounded having a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask an experienced concerning this green wire connection. Some will say to let it rest be, i.e., do nothing with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends with the mounting bracket with the small screws provided. It covers/hides the sides with the motor along with the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets with the screws and washers provided. Then mount the blades for the bottom side of fan motor with the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to help keep them separate from the rest with the kit hardware.
Tip: to help keep the motor from becoming too off-level with this step, install the blades one by one opposite to each other to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just under the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided in the event the lighting assembly is not wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on with the wall switch, even though the fan itself is controlled through the pull-chain switch only, initially set inside off position. Note: The ceiling fan features a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.
