Harbor Ceiling Fans – The flush-style ceiling fan is mounted snugly beside a set horizontal fairly low ceiling where it’s taken care of, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of the room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the instruments and possible other parts needed for installing them, their self-assemble kits have any devices. In many cases, the fan, which will have its lighting, will replace a ceiling permanent fixture.
Safety, The electricity has to be off at the site the place that the fan shall be installed. If the fan is replacing a permanent fixture, turn off its fuse or circuit breaker in addition to flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; tend not to lean or enter into a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if required
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the permanent fixture from the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws from the electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to this fixture are cold (quality light will always be off). Cut the wires, leaving 3-5″ of tail for connecting these to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one as well as a white one. Tip: also look into the firmness with the electrical box in the ceiling. If it’s not solidly coupled to the ceiling, add two extra screws to its top side, which could require drilling two holes in the box on their behalf. The ceiling fan is heavier compared to permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires in the junction box cleanly, install the mounting bracket to the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger in to the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor as well as a blue or off-color one for your lights to become attached below it. Overlap the stripped ends of such two wires (motor and lights) together using the stripped end with the black ceiling wire in the box, and twist connect them together using the wire nut provided. Connect the white assembly wire to the white ceiling wire exactly the same way.
Then, to maintain these connections from loosening as the fan is working, tape the wide lower ends of such nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) to the electrical box in the event the box is additionally grounded with a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask a specialist concerning this green wire connection. Some will say to let it rest be, i.e., do nothing at all from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends with the mounting bracket using the small screws provided. It covers/hides the sides with the motor and the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets using the screws and washers provided. Then mount the blades to the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to maintain them separate from the rest with the kit hardware.
Tip: to maintain the motor from becoming too off-level with this step, install the blades individually opposite to one another to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just beneath the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided in the event the lighting assembly just isn’t wanted without any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on using the wall switch, as the fan itself is controlled by the pull-chain switch only, initially set in the off position. Note: The ceiling fan carries a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.