Dc Motor Ceiling Fans – Two reasons to put in a ceiling fan, heating and cooling. If you live in a cold climate, fans can push hot air gathered nearby the ceiling back off. Ceiling fans might be simple to install when you have some mechanical aptitude. Current ceiling fans include remote-controls to vary speed and adjust lighting. If your room already features a light fixture inside the ceiling, your light fixture probably has one hot or feed wire likely to it, the neutral white and also the bonding green or copper. Essentially it is a three-wire system. Many new construction homes have four wires available, one for your light and something for your fan motor control and also the neutral and ground. If you just have one Hot wire feeding the ceiling junction box, the remote-control fans will continue to work using your application. Additionally some remote-controlled fans use wall controller which sends its signal for the fan being a TV remote. It just seems like a wall control unit. If you only need the energy wire for the remote-controlled fan, please cap off of the fourth wire which you will not need to use. This must be shown within your directions that had the fan assembly.
Once you have acquired an admirer you prefer, build it according for the instructions given. Some fans really are a much more complex, ask a pal to aid if you need to. It is best to help it become assembled correctly, using a ceiling fan blade thud your self on the top might be annoying. Once you have the pre-assembly completed, you can now prepare the ceiling junction box. Of course I know you have already ensured the energy for the ceiling box is powered down no it’s possible to energize it accidentally. Once you have performed this, you need to find three wires inside the J-box. A copper or green wire for bonding. A white wire for your neutral as well as a red or black wire for your power. If your junction box features a fourth wire, this would be setup for any wall controlled fan switch which can be great and allows you to use a non-remote wall controller. I should mention that some all fans include a wall controllers designed as remotes so don’t be confused since these all help the singular feed within your ceiling junction box.
A word about weight, not yours but a word about the sized your fan. If you have a large fan and it is weighted near 12 pounds or more, you will need a special junction box that will support the excess weight. I would recommend you may well ask somebody who knows about these heavier fans if that’s what you will be likely to install. Most fans are lighter and might be placed in most junction boxes without modifications.
Now why don’t we get it down there, the fan that is. Many fans include a Hanger in the shape of a U. Install this hanger on your box, the screws must be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you have the hanger installed, get your fan motor devoid of the blades installed and place it around the hanger. This allows you the electrician to hook up the wires without struggling to juggle the motor and wire it simultaneously. Connect the bonding wire for the chassis as noted inside the instructions. Next connect the white neutral wire, and after this the black wire. Swing the fan into place while using the parts provided. Some have brackets, some make use of a metal plate while some use preformed mounting bases. Use your instructions you’ll also find an admirer right away. Smaller fans might require you to pre-assemble your blades before hanging the fan. I always found installing the motor first then installing the blades last is much simpler. It does require however, you to work above your face to obtain the blades attached.
Once you have the fan hanging, the blades installed and everything tightened you can now step off of the ladder, relax, then install the wall controller as provided. These all vary in design however they all follow similar procedures. Remember, you will have a line and load situation here. This means, the line side is the group of wires the feed in the switch box from your panel while the Load side is likely to your fan. This is critical so ensure you see the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next perform the Line (incoming) side next: Bond or ground should already be made up for the new controller. Next wire your white neutral for the controllers neutral for your Line side. You may have already wired your neutrals together according to your instructions. Now wire your Hot or Power wire for the Line side of the controller. If you have the fourth wire in that room, cap it well or use it for your motor control and connect it accordingly for your directions. Red to Red is usually the case here. Once completed, be some Iced Tea and enjoy your fan.