Monte Carlo Mini 20 20 In Brushed Steel Ceiling Fan 4mc20bs The for measurements 1000 X 1000Small Outdoor Ceiling Fans With Light – The flush-style ceiling fan is mounted snugly alongside a set horizontal fairly low ceiling where it is taken care of, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, according to the room size being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the equipment and possible the rest needed for installing them, their self-assemble kits include anything else. In many cases, the fan, that will have its own lighting, will replace a ceiling light fixture.
Safety, The electricity has to be off at the site in which the fan is to be installed. If the fan is replacing a light fixture, power down its fuse or circuit breaker in addition to flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder through the installation; usually do not lean or enter into a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, as appropriate
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the light fixture from your ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws from your electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to the fixture are cold (quality light will always be off). Cut the wires, leaving 3-5″ of tail to get in touch these to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one along with a white one. Tip: also confirm the firmness with the electrical box inside the ceiling. If it is not solidly coupled to the ceiling, add two extra screws to its top side, which might require drilling two holes inside the box for the children. The ceiling fan is heavier compared to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires inside the junction box cleanly, install the mounting bracket to the box with the two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in to the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor along with a blue or off-color one for the lights to be attached below it. Overlap the stripped ends of those two wires (motor and lights) together with the stripped end with the black ceiling wire inside the box, and twist connect them together with the wire nut provided. Connect the white assembly wire to the white ceiling wire much the same way.
Then, to maintain these connections from loosening as the fan is working, tape the wide lower ends of those nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) to the electrical box if your box is also grounded with a third bare or green wire. Otherwise, if your electrical box in not grounded, ask an expert about this green wire connection. Some will say to get forced out be, i.e., do nothing by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends with the mounting bracket with the small screws provided. It covers/hides the perimeters with the motor along with the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets with the screws and washers provided. Then mount the blades to the bottom side of fan motor with the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to maintain them separate from your rest with the kit hardware.
Tip: to maintain the motor from becoming too off-level within this step, install the blades one at a time opposite to each other in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just under the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided if your lighting assembly isn’t wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on with the wall switch, as the fan itself is controlled through the pull-chain switch only, initially set inside the off position. Note: The ceiling fan carries a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.
