Seagull Ceiling Fans – Two reasons to install a ceiling fan, cooling and heating. If you live in a very cold climate, fans can push heated air gathered close to the ceiling back down. Ceiling fans can be all to easy to install when you have some mechanical aptitude. Current ceiling fans have remote-controls to vary speed and adjust lighting. If your room already has a permanent fixture in the ceiling, your permanent fixture probably has one hot or feed wire likely to it, the neutral white and the bonding green or copper. Essentially this is the three-wire system. Many new construction homes have four wires available, one for that light and one for that fan motor control and the neutral and ground. If you have only one Hot wire feeding the ceiling junction box, the remote-control fans work using your application. Additionally some remote-controlled fans use wall controller which sends its signal towards the fan as being a TV remote. It just appears to be a wall control unit. If you only need the electricity wire for your remote-controlled fan, please cap over fourth wire which you will not want to work with. This should be shown within your directions that came with the fan assembly.
Once you might have acquired a fan you want, assemble it according towards the instructions given. Some fans are a little more complex, ask a pal to help you if necessary. It is best to makes it assembled correctly, developing a ceiling fan blade thud yourself the pinnacle can be annoying. Once you might have the pre-assembly completed, anyone can prepare the ceiling junction box. Of course I know you might have already made sure the electricity towards the ceiling box is powered down and no one can energize it accidentally. Once you might have performed this, you ought to find three wires in the J-box. A copper or green wire for bonding. A white wire for that neutral plus a red or black wire for that power. If your junction box has a fourth wire, this is build for any wall controlled fan switch which can be great and allows you to work with a non-remote wall controller. I should mention that some all fans have a wall controllers designed as remotes so avoid being confused because they all use the singular feed within your ceiling junction box.
A word about weight, not yours but anything concerning the size your fan. If you might have a substantial fan and its particular weighted near 12 pounds or higher, you will need a special junction box that could support the more weight. I would recommend i hear you ask somebody who knows about these heavier fans if that is what you’re likely to install. Most fans are lighter and can be set up in most junction boxes without modifications.
Now why don’t we get up there, the fan that’s. Many fans have a Hanger in the shape of a U. Install this hanger on your box, the screws should be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you might have the hanger installed, grab your fan motor without the blades installed and hang it on the hanger. This allows you the electrician to connect the wires without struggling to juggle the motor and wire it as well. Connect the bonding wire towards the chassis as noted in the instructions. Next connect the white neutral wire, and today the black wire. Swing the fan into place using the parts provided. Some have brackets, some work with a metal plate while others use preformed mounting bases. Use your instructions you’ll also find a fan right away. Smaller fans might require you to pre-assemble your blades before hanging the fan. I always found installing the motor first then installing the blades last is much easier. It does require however, you to work above your brain to find the blades attached.
Once you might have the fan hanging, the blades installed and everything tightened anyone can step over ladder, relax, then install the wall controller as provided. These all vary in design but they all follow similar procedures. Remember, you will have a line and load situation here. This means, the road side will be the set of wires the feed in the switch box through the panel whilst the Load side is likely to your fan. This is critical so make sure you comprehend the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next do the Line (incoming) side next: Bond or ground should already be constructed towards the new controller. Next wire your white neutral towards the controllers neutral for that Line side. You may have already wired your neutrals together as outlined by your instructions. Now wire your Hot or Power wire towards the Line side of the controller. If you might have the fourth wire within, cap rid of it or use it for that motor control and connect it accordingly for a directions. Red to Red is often the case here. Once completed, make yourself some Iced Tea and get your brand-new fan.