68 Inch Ceiling Fan – Two reasons to put in a ceiling fan, heating and cooling. If you live in a cold climate, fans can push warm air gathered near the ceiling back. Ceiling fans can be easy to install when you have some mechanical aptitude. Current ceiling fans have remote-controls to vary speed and adjust lighting. If your room already includes a light fixture within the ceiling, your light fixture probably has one hot or feed wire likely to it, the neutral white and the bonding green or copper. Essentially this can be a three-wire system. Many new construction homes have four wires available, one for your light and something for your fan motor control and the neutral and ground. If you just have one Hot wire feeding the ceiling junction box, the remote-control fans work using your application. Additionally some remote-controlled fans use wall controller which sends its signal to the fan like a TV remote. It just seems like a wall control unit. If you just have the power wire on your remote-controlled fan, please cap off of the fourth wire which you will not require to utilize. This must be shown with your directions that included the fan assembly.
Once you might have acquired an admirer you prefer, build it according to the instructions given. Some fans certainly are a extra complex, ask a friend to help if required. It is best to make sure it is assembled correctly, creating a ceiling fan blade thud you on the top can be annoying. Once you might have the pre-assembly completed, you can now prepare the ceiling junction box. Of course I know you might have already made certain the power to the ceiling box is deterred no you can energize it accidentally. Once you might have performed this, you must find three wires within the J-box. A copper or green wire for bonding. A white wire for your neutral along with a red or black wire for your power. If your junction box includes a fourth wire, this would be set up to get a wall controlled fan switch which is great and allows you to utilize a non-remote wall controller. I should mention that some all fans have a wall controllers designed as remotes so avoid being confused as these all assist the singular feed with your ceiling junction box.
A word about weight, not yours but a thing about the size of your fan. If you might have a big fan and it is weighted near 12 pounds or maybe more, you might need a special junction box that could support the more weight. I would recommend you may ask someone who knows about these heavier fans recommendations what you really are likely to install. Most fans are lighter and can be set up in most junction boxes without modifications.
Now let’s get it there, the fan that is. Many fans have a Hanger the same shape as a U. Install this hanger onto your box, the screws must be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you might have the hanger installed, grab your fan motor with no blades installed and hang it on the hanger. This allows you the electrician to attach the wires without struggling to juggle the motor and wire it at the same time. Connect the bonding wire to the chassis as noted within the instructions. Next connect the white neutral wire, now the black wire. Swing the fan into place with all the parts provided. Some have brackets, some use a metal plate and some use preformed mounting bases. Use your instructions and you’ll have an admirer right away. Smaller fans may necessitate one to pre-assemble your blades before hanging the fan. I always found installing the motor first after which installing the blades last is much easier. It does require however, one to work above your head to obtain the blades attached.
Once you might have the fan hanging, the blades installed and everything tightened you can now step off of the ladder, relax, then install the wall controller as provided. These all vary in design however they all follow similar procedures. Remember, you will have a line and load situation here. This means, the queue side may be the list of wires the feed in to the switch box from your panel while the Load side is likely to your fan. This is critical so be sure to view the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next perform Line (incoming) side next: Bond or ground should already be made up to the new controller. Next wire your white neutral to the controllers neutral for your Line side. You may have already wired your neutrals together based on your instructions. Now wire your Hot or Power wire to the Line side of the controller. If you might have the fourth wire in there, cap it well or use it for your motor control and connect it accordingly for a directions. Red to Red is often the case here. Once completed, make yourself some Iced Tea and luxuriate in your brand-new fan.