Ge Ceiling Fan – Two why you should install a ceiling fan, air conditioning. If you live in a cold climate, fans can push warm air gathered at the ceiling down again. Ceiling fans can be easy to install for those who have some mechanical aptitude. Current ceiling fans include remote-controls to vary speed and adjust lighting. If your room already includes a fitting in the ceiling, your fitting probably has one hot or feed wire gonna it, the neutral white as well as the bonding green or copper. Essentially this is a three-wire system. Many new construction homes have four wires available, one to the light and something to the fan motor control as well as the neutral and ground. If you have only one Hot wire feeding the ceiling junction box, the remote-control fans work together with your application. Additionally some remote-controlled fans use wall controller which sends its signal to the fan just like a TV remote. It just seems like a wall control unit. If you only need the electricity wire for your remote-controlled fan, please cap off the fourth wire which you will not want to use. This should be shown within your directions that was included with the fan assembly.
Once you’ve acquired a lover you prefer, put it together according to the instructions given. Some fans can be a extra complex, ask an associate to help if required. It is best to makes it assembled correctly, using a ceiling fan blade thud your self on the head can be annoying. Once you’ve the pre-assembly completed, it’s simple to prepare the ceiling junction box. Of course I know you’ve already made certain the electricity to the ceiling box is switched off and no you can energize it accidentally. Once you’ve succeeded in doing so, you should find three wires in the J-box. A copper or green wire for bonding. A white wire to the neutral plus a red or black wire to the power. If your junction box includes a fourth wire, this is set up to get a wall controlled fan switch which can be great and allows you to use a non-remote wall controller. I should mention that some all fans include a wall controllers designed as remotes so you shouldn’t be confused as these all assist the singular feed within your ceiling junction box.
A word about weight, not yours but a thing in regards to the size your fan. If you’ve a substantial fan and it is weighted near 12 pounds or higher, you might need a special junction box that may keep the additional weight. I would recommend i hear you ask somebody who knows about these heavier fans if that’s what you are gonna install. Most fans are lighter and can be set up in most junction boxes without modifications.
Now why don’t we get it there, the fan that is. Many fans include a Hanger the same shape as a U. Install this hanger on to your box, the screws should be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you’ve the hanger installed, grab your fan motor devoid of the blades installed and place it around the hanger. This allows you the electrician to hook up the wires without struggling to juggle the motor and wire it at the same time. Connect the bonding wire to the chassis as noted in the instructions. Next connect the white neutral wire, and now the black wire. Swing the fan into place with all the parts provided. Some have brackets, some make use of a metal plate while others use preformed mounting bases. Use your instructions and you’ll have a lover quickly. Smaller fans may necessitate one to pre-assemble your blades before hanging the fan. I always found installing the motor first then installing the blades last is much easier. It does require however, one to work above your face to get the blades attached.
Once you’ve the fan hanging, the blades installed and everything tightened it’s simple to step off the ladder, relax, then install the wall controller as provided. These all vary in design nonetheless they all follow similar procedures. Remember, you will have a line and load situation here. This means, the road side may be the pair of wires the feed in to the switch box through the panel while the Load side is gonna your fan. This is critical so make sure you see the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next do the Line (incoming) side next: Bond or ground should already be comprised to the new controller. Next wire your white neutral to the controllers neutral to the Line side. You may have already wired your neutrals together in accordance with your instructions. Now wire your Hot or Power wire to the Line side of your respective controller. If you’ve the fourth wire within, cap it off or use it to the motor control and connect it accordingly for a directions. Red to Red is truly the case here. Once completed, make yourself some Iced Tea and luxuriate in your new fan.