Wall Mounted Ceiling Fans – The flush-style ceiling fan is mounted snugly close to a flat horizontal fairly low ceiling where it really is out of the way, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, according to the size of room being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the instruments and possible other areas needed for installing them, their self-assemble kits feature the rest. In many cases, the fan, that can have its lighting, will replace a ceiling light fixture.
Safety, The electricity have to be off once your there where the fan is to be installed. If the fan is replacing a light fixture, de-activate its fuse or circuit breaker together with flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; tend not to lean or enter a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if required
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the light fixture through the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws through the electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to the fixture are cold (the exam light will remain off). Cut the wires, leaving 3-5″ of tail in order to connect these phones the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one and a white one. Tip: also look into the firmness from the electrical box in the ceiling. If it really is not solidly coupled to the ceiling, add two extra screws to its top side, which could require drilling two holes in the box on their behalf. The ceiling fan is heavier as opposed to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires in the junction box cleanly, install the mounting bracket on the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger in the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor and a blue or off-color one for that lights to become attached below it. Overlap the stripped ends of the two wires (motor and lights) together using the stripped end from the black ceiling wire in the box, and twist connect them together using the wire nut provided. Connect the white assembly wire on the white ceiling wire exactly the same way.
Then, to keep these connections from loosening as the fan is working, tape the wide lower ends of the nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) on the electrical box if your box can be grounded having a third bare or green wire. Otherwise, if your electrical box in not grounded, ask an experienced relating to this green wire connection. Some will say to let it rest be, i.e., do nothing at all with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends from the mounting bracket using the small screws provided. It covers/hides the perimeters from the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets using the screws and washers provided. Then mount the blades on the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to keep them separate through the rest from the kit hardware.
Tip: to keep the motor from becoming too off-level in this step, install the blades one at a time opposite to one another in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just under the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided if your lighting assembly is not wanted without any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on using the wall switch, as the fan itself is controlled through the pull-chain switch only, initially set in the off position. Note: The ceiling fan features a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.