Living Room Ceiling Fan – The flush-style ceiling fan is mounted snugly next to a flat horizontal fairly low ceiling where it really is off the beaten track, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of the room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the tools and possible the rest required for installing them, their self-assemble kits come with everything else. In many cases, the fan, that may have its lighting, will replace a ceiling light fixture.
Safety, The electricity have to be off once your there the location where the fan will be installed. If the fan is replacing a light fixture, power down its fuse or circuit breaker in addition to flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; usually do not lean or enter into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is required, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, as appropriate
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the light fixture through the ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws through the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to this fixture are cold (the exam light will stay off). Cut the wires, leaving 3-5″ of tail for connecting these to the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one along with a white one. Tip: also look at the firmness of the electrical box within the ceiling. If it really is not solidly attached to the ceiling, add two extra screws to its top side, which might require drilling two holes within the box for them. The ceiling fan is heavier than the light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires within the junction box cleanly, install the mounting bracket to the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor along with a blue or off-color one to the lights to get attached below it. Overlap the stripped ends of these two wires (motor and lights) together while using stripped end of the black ceiling wire within the box, and twist connect them together while using wire nut provided. Connect the white assembly wire to the white ceiling wire much the same way.
Then, to help keep these connections from loosening even though the fan is working, tape the wide lower ends of these nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) to the electrical box if the box can be grounded having a third bare or green wire. Otherwise, if the electrical box in not grounded, ask a professional about this green wire connection. Some will say to let it sit be, i.e., relax with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends of the mounting bracket while using small screws provided. It covers/hides the perimeters of the motor and the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets while using screws and washers provided. Then mount the blades to the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to help keep them separate through the rest of the kit hardware.
Tip: to help keep the motor from becoming too off-level during this step, install the blades one-by-one opposite together to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just under the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided if the lighting assembly is not wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on while using wall switch, even though the fan itself is controlled by the pull-chain switch only, initially set within the off position. Note: The ceiling fan features a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.