Hugger 52 In Led Indoor Brushed Nickel Ceiling Fan With Light Kit intended for sizing 1000 X 1000Ceiling Fan Led – The flush-style ceiling fan is mounted snugly next to a flat horizontal fairly low ceiling where it’s out of the way, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of the room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the instruments and possible other parts necessary for installing them, their self-assemble kits include anything else. In many cases, the fan, which will have its very own lighting, will replace a ceiling light fixture.
Safety, The electricity have to be off to begin the location where the fan is to be installed. If the fan is replacing a light fixture, shut down its fuse or circuit breaker along with flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder through the installation; usually do not lean or enter into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if needed
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the light fixture from your ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws from your electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections for this fixture are cold (quality light will always be off). Cut the wires, leaving 3-5″ of tail in order to connect the crooks to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one and a white one. Tip: also check the firmness of the electrical box in the ceiling. If it’s not solidly attached to the ceiling, add two extra screws to its top side, which can require drilling two holes in the box for them. The ceiling fan is heavier as opposed to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires in the junction box cleanly, install the mounting bracket to the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor and a blue or off-color one for the lights being attached below it. Overlap the stripped ends of such two wires (motor and lights) together with all the stripped end of the black ceiling wire in the box, and twist connect them together with all the wire nut provided. Connect the white assembly wire to the white ceiling wire much the same way.
Then, to hold these connections from loosening whilst the fan is working, tape the wide lower ends of such nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) to the electrical box when the box can also be grounded using a third bare or green wire. Otherwise, when the electrical box in not grounded, ask a professional relating to this green wire connection. Some will say to let it sit be, i.e., do nothing at all from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends of the mounting bracket with all the small screws provided. It covers/hides the edges of the motor and the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets with all the screws and washers provided. Then mount the blades to the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to hold them separate from your rest of the kit hardware.
Tip: to hold the motor from becoming too off-level within this step, install the blades individually opposite to one another first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just beneath the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided when the lighting assembly is not wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on with all the wall switch, whilst the fan itself is controlled with the pull-chain switch only, initially set in the off position. Note: The ceiling fan has a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.
