Dual Motor Ceiling Fan – The flush-style ceiling fan is mounted snugly alongside a set horizontal fairly low ceiling where it really is taken care of, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, depending on the room size being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the equipment and possible other parts required for installing them, their self-assemble kits feature any devices. In many cases, the fan, that may have its lighting, will replace a ceiling light fixture.
Safety, The electricity should be off to begin in which the fan is usually to be installed. If the fan is replacing a light fixture, de-activate its fuse or circuit breaker together with flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; usually do not lean or end up in a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if needed
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the light fixture from the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws from the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to this fixture are cold (quality light will stay off). Cut the wires, leaving 3-5″ of tail in order to connect these phones the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one as well as a white one. Tip: also check the firmness from the electrical box inside ceiling. If it really is not solidly connected to the ceiling, add two extra screws to its top side, which could require drilling two holes inside box on their behalf. The ceiling fan is heavier as opposed to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires inside junction box cleanly, install the mounting bracket towards the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger to the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor as well as a blue or off-color one for your lights to be attached below it. Overlap the stripped ends of those two wires (motor and lights) together while using stripped end from the black ceiling wire inside box, and twist connect them together while using wire nut provided. Connect the white assembly wire towards the white ceiling wire exactly the same way.
Then, to keep these connections from loosening as the fan is working, tape the wide lower ends of those nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) towards the electrical box if the box is also grounded with a third bare or green wire. Otherwise, if the electrical box in not grounded, ask a professional about this green wire connection. Some will say to get forced out be, i.e., relax by using it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends from the mounting bracket while using small screws provided. It covers/hides the edges from the motor along with the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets while using screws and washers provided. Then mount the blades towards the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to keep them separate from the rest from the kit hardware.
Tip: to keep the motor from becoming too off-level during this step, install the blades one by one opposite to each other to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just beneath the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided if the lighting assembly is just not wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on while using wall switch, as the fan itself is controlled from the pull-chain switch only, initially set inside off position. Note: The ceiling fan carries a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.