Hunter Crown Canyon 52 In Indoor Regal Bronze Ceiling Fan 53331 throughout measurements 1000 X 1000Rustic Looking Ceiling Fans – Two good reasons to put in a ceiling fan, air conditioning. If you live in a cold climate, fans can push hot air gathered near the ceiling back down. Ceiling fans could be an easy task to install in case you have some mechanical aptitude. Current ceiling fans come with remote-controls to vary speed and adjust lighting. If your room already features a permanent fixture within the ceiling, your permanent fixture probably has one hot or feed wire likely to it, the neutral white as well as the bonding green or copper. Essentially it is a three-wire system. Many new construction homes have four wires available, one for that light the other for that fan motor control as well as the neutral and ground. If you just have one Hot wire feeding the ceiling junction box, the remote-control fans will continue to work using your application. Additionally some remote-controlled fans use wall controller which sends its signal to the fan being a TV remote. It just appears to be a wall control unit. If you really need the power wire for your remote-controlled fan, please cap over fourth wire which you will not require to use. This should be shown with your directions that was included with the fan assembly.
Once you’ve acquired a follower that suits you, put it together according to the instructions given. Some fans can be a little more complex, ask a buddy to help if need be. It is best to make sure it is assembled correctly, creating a ceiling fan blade thud yourself your head could be annoying. Once you’ve the pre-assembly completed, now you can prepare the ceiling junction box. Of course I know you’ve already made sure the power to the ceiling box is powered down and no you can energize it accidentally. Once you’ve carried this out, you should find three wires within the J-box. A copper or green wire for bonding. A white wire for that neutral and a red or black wire for that power. If your junction box features a fourth wire, this is build for a wall controlled fan switch that is great and allows you to use a non-remote wall controller. I should mention that some all fans come with a wall controllers designed as remotes so do not be confused because these all assist the singular feed with your ceiling junction box.
A word about weight, not yours but anything concerning the size your fan. If you’ve a sizable fan as well as weighted near 12 pounds or more, you need a special junction box that could keep the additional weight. I would recommend you ask somebody who knows about these heavier fans if that’s what you will be likely to install. Most fans are lighter and could be set up in most junction boxes without modifications.
Now let’s get it up there, the fan that’s. Many fans come with a Hanger the same shape as a U. Install this hanger onto your box, the screws should be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you’ve the hanger installed, pick-up your fan motor with no blades installed and hang up it for the hanger. This allows you the electrician to attach the wires without struggling to juggle the motor and wire it simultaneously. Connect the bonding wire to the chassis as noted within the instructions. Next connect the white neutral wire, and now the black wire. Swing the fan into place using the parts provided. Some have brackets, some use a metal plate although some use preformed mounting bases. Use your instructions you’ll also find a follower in no time. Smaller fans may necessitate that you pre-assemble your blades before hanging the fan. I always found installing the motor first after which installing the blades last is much simpler. It does require however, that you work above your head to get the blades attached.
Once you’ve the fan hanging, the blades installed and everything tightened now you can step over ladder, relax, then install the wall controller as provided. These all vary in design nevertheless they all follow similar procedures. Remember, you will have a line and load situation here. This means, the line side may be the group of wires the feed in the switch box through the panel as the Load side is likely to your fan. This is critical so make sure you understand the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next do the Line (incoming) side next: Bond or ground should already be composed to the new controller. Next wire your white neutral to the controllers neutral for that Line side. You may have already wired your neutrals together according to your instructions. Now wire your Hot or Power wire to the Line side of one’s controller. If you’ve the fourth wire in that room, cap it off or use it for that motor control and connect it accordingly for your directions. Red to Red is usually the case here. Once completed, make yourself some Iced Tea and revel in your brand-new fan.
