Hampton Bay Sidewinder 54 In Indoor Brushed Nickel Ceiling Fan With intended for sizing 1000 X 1000Ceiling Fans With Remote – The flush-style ceiling fan is mounted snugly alongside a set horizontal fairly low ceiling where it really is off the beaten track, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, depending on the room size being fitted, and can cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the tools and possible other regions necessary for installing them, their self-assemble kits include the rest. In many cases, the fan, which will have a unique lighting, will replace a ceiling fitting.
Safety, The electricity must be off at the site the place that the fan is usually to be installed. If the fan is replacing a fitting, turn off its fuse or circuit breaker as well as flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; usually do not lean or enter into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if needed
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the fitting in the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws in the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections for this fixture are cold (test light will always be off). Cut the wires, leaving 3-5″ of tail for connecting these to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one plus a white one. Tip: also confirm the firmness of the electrical box within the ceiling. If it really is not solidly coupled to the ceiling, add two extra screws to its top side, which could require drilling two holes within the box for the kids. The ceiling fan is heavier than the fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires within the junction box cleanly, install the mounting bracket on the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor plus a blue or off-color one for the lights to get attached below it. Overlap the stripped ends of those two wires (motor and lights) together using the stripped end of the black ceiling wire within the box, and twist connect them together using the wire nut provided. Connect the white assembly wire on the white ceiling wire exactly the same.
Then, to help keep these connections from loosening whilst the fan is working, tape the wide lower ends of those nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) on the electrical box if the box can also be grounded having a third bare or green wire. Otherwise, if the electrical box in not grounded, ask an expert concerning this green wire connection. Some will say to get forced out be, i.e., relax by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends of the mounting bracket using the small screws provided. It covers/hides the edges of the motor and also the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets using the screws and washers provided. Then mount the blades on the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to help keep them separate in the rest of the kit hardware.
Tip: to help keep the motor from becoming too off-level with this step, install the blades one by one opposite together in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just underneath the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided if the lighting assembly isn’t wanted without any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on using the wall switch, whilst the fan itself is controlled from the pull-chain switch only, initially set within the off position. Note: The ceiling fan includes a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.
