Design House Martinique 52 In Indooroutdoor Oil Rubbed Bronze in size 1000 X 1000House Ceiling Fans – The flush-style ceiling fan is mounted snugly alongside a flat horizontal fairly low ceiling where it really is out of the way, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of room being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the equipment and possible the rest necessary for installing them, their self-assemble kits have any devices. In many cases, the fan, that will have its lighting, will replace a ceiling permanent fixture.
Safety, The electricity must be off once your there in which the fan shall be installed. If the fan is replacing a permanent fixture, de-activate its fuse or circuit breaker along with flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; tend not to lean or enter a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if required
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the permanent fixture in the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws in the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to the fixture are cold (the exam light will stay off). Cut the wires, leaving 3-5″ of tail to get in touch the crooks to the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one and a white one. Tip: also look at the firmness in the electrical box inside ceiling. If it really is not solidly connected to the ceiling, add two extra screws to its top side, that might require drilling two holes inside box for the kids. The ceiling fan is heavier compared to the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires inside junction box cleanly, install the mounting bracket to the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger to the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor and a blue or off-color one for that lights to get attached below it. Overlap the stripped ends of the two wires (motor and lights) together while using stripped end in the black ceiling wire inside box, and twist connect them together while using wire nut provided. Connect the white assembly wire to the white ceiling wire the same way.
Then, to maintain these connections from loosening while the fan is working, tape the wide lower ends of the nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) to the electrical box if your box can be grounded using a third bare or green wire. Otherwise, if your electrical box in not grounded, ask an expert relating to this green wire connection. Some will say to let it rest be, i.e., do nothing with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends in the mounting bracket while using small screws provided. It covers/hides the perimeters in the motor and also the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets while using screws and washers provided. Then mount the blades to the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to maintain them separate in the rest in the kit hardware.
Tip: to maintain the motor from becoming too off-level during this step, install the blades one by one opposite to each other first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just beneath the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided if your lighting assembly isn’t wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on while using wall switch, while the fan itself is controlled through the pull-chain switch only, initially set inside off position. Note: The ceiling fan features a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.
