Vaxcel Lighting Sebring Ceiling Fan Model Fn52997or In Vintage Bronze intended for size 2400 X 1265Vaxcel Ceiling Fans – The flush-style ceiling fan is mounted snugly alongside an appartment horizontal fairly low ceiling where it is off the beaten track, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the instruments and possible other areas required for installing them, their self-assemble kits include the rest. In many cases, the fan, which will have a unique lighting, will replace a ceiling permanent fixture.
Safety, The electricity must be off at the site the place that the fan is to be installed. If the fan is replacing a permanent fixture, turn off its fuse or circuit breaker together with flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; tend not to lean or enter a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if necessary
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the permanent fixture from your ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws from your electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to this particular fixture are cold (the test light will continue to be off). Cut the wires, leaving 3-5″ of tail to get in touch them to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one as well as a white one. Tip: also look at the firmness of the electrical box inside ceiling. If it is not solidly attached to the ceiling, add two extra screws to its top side, that might require drilling two holes inside box for them. The ceiling fan is heavier compared to permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires inside junction box cleanly, install the mounting bracket for the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor as well as a blue or off-color one for your lights to be attached below it. Overlap the stripped ends of these two wires (motor and lights) together while using stripped end of the black ceiling wire inside box, and twist connect them together while using wire nut provided. Connect the white assembly wire for the white ceiling wire much the same way.
Then, to hold these connections from loosening as the fan is working, tape the wide lower ends of these nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) for the electrical box in the event the box can be grounded with a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask an expert about it green wire connection. Some will say to leave it be, i.e., relax from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends of the mounting bracket while using small screws provided. It covers/hides the sides of the motor along with the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets while using screws and washers provided. Then mount the blades for the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to hold them separate from your rest of the kit hardware.
Tip: to hold the motor from becoming too off-level in this step, install the blades individually opposite together to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just underneath the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided in the event the lighting assembly isn’t wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on while using wall switch, as the fan itself is controlled through the pull-chain switch only, initially set inside off position. Note: The ceiling fan has a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.
