J D Mfg Variable Speed Control 5 Amp Model Cn5 Northern pertaining to size 2000 X 2000Ceiling Fan Variable Speed Control – The flush-style ceiling fan is mounted snugly close to a set horizontal fairly low ceiling where it really is off the beaten track, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the room size being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the equipment and possible other regions necessary for installing them, their self-assemble kits include any devices. In many cases, the fan, that can have its very own lighting, will replace a ceiling permanent fixture.
Safety, The electricity have to be off to begin the location where the fan shall be installed. If the fan is replacing a permanent fixture, shut down its fuse or circuit breaker in addition to flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; usually do not lean or enter into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is required, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if required
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the permanent fixture through the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws through the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to the fixture are cold (quality light will remain off). Cut the wires, leaving 3-5″ of tail in order to connect these phones the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one and a white one. Tip: also confirm the firmness of the electrical box inside ceiling. If it really is not solidly coupled to the ceiling, add two extra screws to its top side, which might require drilling two holes inside box for the children. The ceiling fan is heavier compared to the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires inside junction box cleanly, install the mounting bracket on the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger in to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor and a blue or off-color one to the lights being attached below it. Overlap the stripped ends of these two wires (motor and lights) together with all the stripped end of the black ceiling wire inside box, and twist connect them together with all the wire nut provided. Connect the white assembly wire on the white ceiling wire exactly the same way.
Then, to keep these connections from loosening while the fan is working, tape the wide lower ends of these nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) on the electrical box in the event the box can also be grounded using a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask an expert relating to this green wire connection. Some will say to let it rest be, i.e., do nothing at all by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends of the mounting bracket with all the small screws provided. It covers/hides the sides of the motor along with the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets with all the screws and washers provided. Then mount the blades on the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to keep them separate through the rest of the kit hardware.
Tip: to keep the motor from becoming too off-level during this step, install the blades one by one opposite to one another to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just underneath the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided in the event the lighting assembly is not wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on with all the wall switch, while the fan itself is controlled with the pull-chain switch only, initially set inside off position. Note: The ceiling fan features a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.
