Lighting Chandelier With Ceiling Fan Attached For Cozy Lighting inside size 835 X 1002Chandelier With Ceiling Fan Attached – The flush-style ceiling fan is mounted snugly next to a flat horizontal fairly low ceiling where it is dealt with, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of the room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the equipment and possible the rest essential for installing them, their self-assemble kits have everything else. In many cases, the fan, which will have its very own lighting, will replace a ceiling light fixture.
Safety, The electricity should be off once your there where the fan shall be installed. If the fan is replacing a light fixture, power down its fuse or circuit breaker together with flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder through the installation; usually do not lean or enter into a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if necessary
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the light fixture from your ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws from your electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to the fixture are cold (the exam light will continue to be off). Cut the wires, leaving 3-5″ of tail for connecting the crooks to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one as well as a white one. Tip: also look at the firmness with the electrical box within the ceiling. If it is not solidly attached to the ceiling, add two extra screws to its top side, which might require drilling two holes within the box for the children. The ceiling fan is heavier compared to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires within the junction box cleanly, install the mounting bracket on the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in to the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor as well as a blue or off-color one to the lights to become attached below it. Overlap the stripped ends of those two wires (motor and lights) together while using stripped end with the black ceiling wire within the box, and twist connect them together while using wire nut provided. Connect the white assembly wire on the white ceiling wire much the same way.
Then, to maintain these connections from loosening while the fan is working, tape the wide lower ends of those nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) on the electrical box if your box can also be grounded with a third bare or green wire. Otherwise, if your electrical box in not grounded, ask an expert about it green wire connection. Some will say to let it rest be, i.e., do nothing at all by using it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends with the mounting bracket while using small screws provided. It covers/hides the perimeters with the motor and the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets while using screws and washers provided. Then mount the blades on the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to maintain them separate from your rest with the kit hardware.
Tip: to maintain the motor from becoming too off-level with this step, install the blades one-by-one opposite to each other to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just underneath the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided if your lighting assembly is just not wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on while using wall switch, while the fan itself is controlled with the pull-chain switch only, initially set within the off position. Note: The ceiling fan includes a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.
