Hugger 52 In Led Indoor Brushed Nickel Ceiling Fan With Light Kit with regard to sizing 1000 X 100052 Inch Ceiling Fan With Light – The flush-style ceiling fan is mounted snugly close to an appartment horizontal fairly low ceiling where it is taken care of, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the room size being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the various tools and possible other regions essential for installing them, their self-assemble kits include anything else. In many cases, the fan, that will have its own lighting, will replace a ceiling permanent fixture.
Safety, The electricity have to be off at the site where the fan will be installed. If the fan is replacing a permanent fixture, de-activate its fuse or circuit breaker along with flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; tend not to lean or get into a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring is required, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, as appropriate
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the permanent fixture in the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws in the electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to the fixture are cold (quality light will stay off). Cut the wires, leaving 3-5″ of tail in order to connect them to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one plus a white one. Tip: also look into the firmness with the electrical box inside the ceiling. If it is not solidly coupled to the ceiling, add two extra screws to its top side, which can require drilling two holes inside the box on their behalf. The ceiling fan is heavier as opposed to permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires inside the junction box cleanly, install the mounting bracket on the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger into the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor plus a blue or off-color one to the lights being attached below it. Overlap the stripped ends of those two wires (motor and lights) together with all the stripped end with the black ceiling wire inside the box, and twist connect them together with all the wire nut provided. Connect the white assembly wire on the white ceiling wire much the same way.
Then, to hold these connections from loosening while the fan is working, tape the wide lower ends of those nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) on the electrical box in the event the box is additionally grounded having a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask a professional about it green wire connection. Some will say to get forced out be, i.e., relax from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends with the mounting bracket with all the small screws provided. It covers/hides the perimeters with the motor and the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets with all the screws and washers provided. Then mount the blades on the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to hold them separate in the rest with the kit hardware.
Tip: to hold the motor from becoming too off-level in this step, install the blades one by one opposite to one another first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just underneath the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided in the event the lighting assembly is not wanted without any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on with all the wall switch, while the fan itself is controlled from the pull-chain switch only, initially set inside the off position. Note: The ceiling fan features a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.
