Casablanca Panama Dc 54 In Indoor Brushed Nickel Ceiling Fan With within measurements 1000 X 1000Casablanca Panama Ceiling Fan – The flush-style ceiling fan is mounted snugly beside a set horizontal fairly low ceiling where it really is off the beaten track, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of the room being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the various tools and possible the rest needed for installing them, their self-assemble kits feature the rest. In many cases, the fan, that will have a unique lighting, will replace a ceiling permanent fixture.
Safety, The electricity should be off at the site where the fan is to be installed. If the fan is replacing a permanent fixture, turn off its fuse or circuit breaker as well as flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; usually do not lean or enter a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if required
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the permanent fixture from your ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws from your electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to this fixture are cold (the exam light will stay off). Cut the wires, leaving 3-5″ of tail allowing you to connect the crooks to the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one and a white one. Tip: also look at the firmness from the electrical box inside the ceiling. If it really is not solidly connected to the ceiling, add two extra screws to its top side, which can require drilling two holes inside the box for them. The ceiling fan is heavier as opposed to permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires inside the junction box cleanly, install the mounting bracket on the box with the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor and a blue or off-color one to the lights to get attached below it. Overlap the stripped ends of those two wires (motor and lights) together with the stripped end from the black ceiling wire inside the box, and twist connect them together with the wire nut provided. Connect the white assembly wire on the white ceiling wire exactly the same way.
Then, to help keep these connections from loosening even though the fan is working, tape the wide lower ends of those nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) on the electrical box if your box is additionally grounded which has a third bare or green wire. Otherwise, if your electrical box in not grounded, ask an expert concerning this green wire connection. Some will say to let it sit be, i.e., relax by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends from the mounting bracket with the small screws provided. It covers/hides the sides from the motor and the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets with the screws and washers provided. Then mount the blades on the bottom side of fan motor with the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to help keep them separate from your rest from the kit hardware.
Tip: to help keep the motor from becoming too off-level within this step, install the blades individually opposite to one another to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just below the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided if your lighting assembly isn’t wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on with the wall switch, even though the fan itself is controlled from the pull-chain switch only, initially set inside the off position. Note: The ceiling fan carries a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.
