Dining Room Ceiling Fans – The flush-style ceiling fan is mounted snugly next to a set horizontal fairly low ceiling where it’s dealt with, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the room size being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the tools and possible the rest necessary for installing them, their self-assemble kits feature the rest. In many cases, the fan, that can have its own lighting, will replace a ceiling fitting.
Safety, The electricity should be off once your there the location where the fan shall be installed. If the fan is replacing a fitting, power down its fuse or circuit breaker as well as flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; tend not to lean or enter a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if necessary
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the fitting from your ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws from your electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to this particular fixture are cold (the test light will remain off). Cut the wires, leaving 3-5″ of tail in order to connect them to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one as well as a white one. Tip: also check the firmness in the electrical box inside ceiling. If it’s not solidly coupled to the ceiling, add two extra screws to its top side, which might require drilling two holes inside box for them. The ceiling fan is heavier than the fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires inside junction box cleanly, install the mounting bracket to the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor as well as a blue or off-color one for that lights to be attached below it. Overlap the stripped ends of these two wires (motor and lights) together while using stripped end in the black ceiling wire inside box, and twist connect them together while using wire nut provided. Connect the white assembly wire to the white ceiling wire exactly the same way.
Then, to hold these connections from loosening while the fan is working, tape the wide lower ends of these nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) to the electrical box if the box can also be grounded with a third bare or green wire. Otherwise, if the electrical box in not grounded, ask a specialist concerning this green wire connection. Some will say to get forced out be, i.e., relax from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends in the mounting bracket while using small screws provided. It covers/hides the perimeters in the motor and also the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets while using screws and washers provided. Then mount the blades to the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to hold them separate from your rest in the kit hardware.
Tip: to hold the motor from becoming too off-level in this step, install the blades one at a time opposite to each other to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just under the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided if the lighting assembly isn’t wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on while using wall switch, while the fan itself is controlled by the pull-chain switch only, initially set inside off position. Note: The ceiling fan carries a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.