Modern White Ceiling Fan – The flush-style ceiling fan is mounted snugly alongside a designated horizontal fairly low ceiling where it can be taken care of, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of room being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the various tools and possible the rest required for installing them, their self-assemble kits have the rest. In many cases, the fan, that can have a unique lighting, will replace a ceiling permanent fixture.
Safety, The electricity have to be off once your there the location where the fan is usually to be installed. If the fan is replacing a permanent fixture, power down its fuse or circuit breaker together with flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; tend not to lean or enter into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if needed
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the permanent fixture through the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws through the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections to this fixture are cold (test light will continue to be off). Cut the wires, leaving 3-5″ of tail for connecting them to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one and a white one. Tip: also look at the firmness of the electrical box within the ceiling. If it can be not solidly coupled to the ceiling, add two extra screws to its top side, which can require drilling two holes within the box for them. The ceiling fan is heavier compared to the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires within the junction box cleanly, install the mounting bracket towards the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger in to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor and a blue or off-color one to the lights to become attached below it. Overlap the stripped ends of those two wires (motor and lights) together while using stripped end of the black ceiling wire within the box, and twist connect them together while using wire nut provided. Connect the white assembly wire towards the white ceiling wire much the same way.
Then, to maintain these connections from loosening whilst the fan is working, tape the wide lower ends of those nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) towards the electrical box in the event the box can also be grounded which has a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask a specialist about it green wire connection. Some will say to let it rest be, i.e., relax with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends of the mounting bracket while using small screws provided. It covers/hides the perimeters of the motor along with the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets while using screws and washers provided. Then mount the blades towards the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to maintain them separate through the rest of the kit hardware.
Tip: to maintain the motor from becoming too off-level in this step, install the blades individually opposite together in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just below the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided in the event the lighting assembly is just not wanted without any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on while using wall switch, whilst the fan itself is controlled from the pull-chain switch only, initially set within the off position. Note: The ceiling fan carries a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.