40 Inch Ceiling Fan – The flush-style ceiling fan is mounted snugly next to an appartment horizontal fairly low ceiling where it really is dealt with, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of room being fitted, and can cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the various tools and possible other areas needed for installing them, their self-assemble kits come with any devices. In many cases, the fan, that may have a unique lighting, will replace a ceiling permanent fixture.
Safety, The electricity must be off to begin where the fan will be installed. If the fan is replacing a permanent fixture, turn off its fuse or circuit breaker along with flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; do not lean or enter into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if needed
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the permanent fixture from the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws from the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to the fixture are cold (the exam light will continue to be off). Cut the wires, leaving 3-5″ of tail in order to connect the crooks to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one along with a white one. Tip: also confirm the firmness in the electrical box inside ceiling. If it really is not solidly attached to the ceiling, add two extra screws to its top side, which could require drilling two holes inside box for the children. The ceiling fan is heavier compared to permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires inside junction box cleanly, install the mounting bracket to the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger to the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor along with a blue or off-color one for that lights being attached below it. Overlap the stripped ends of these two wires (motor and lights) together while using stripped end in the black ceiling wire inside box, and twist connect them together while using wire nut provided. Connect the white assembly wire to the white ceiling wire much the same way.
Then, to hold these connections from loosening as the fan is working, tape the wide lower ends of these nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) to the electrical box when the box is additionally grounded with a third bare or green wire. Otherwise, when the electrical box in not grounded, ask an expert about this green wire connection. Some will say to get forced out be, i.e., do nothing by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends in the mounting bracket while using small screws provided. It covers/hides the edges in the motor along with the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets while using screws and washers provided. Then mount the blades to the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to hold them separate from the rest in the kit hardware.
Tip: to hold the motor from becoming too off-level within this step, install the blades one by one opposite to each other first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just below the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided when the lighting assembly just isn’t wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on while using wall switch, as the fan itself is controlled from the pull-chain switch only, initially set inside off position. Note: The ceiling fan has a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.