Home Decorators Collection Mercer 52 In Led Indoor Brushed Nickel with regard to dimensions 1000 X 1000Remote Control Ceiling Fan Light – The flush-style ceiling fan is mounted snugly next to an appartment horizontal fairly low ceiling where it can be taken care of, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, according to the size of room being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the tools and possible other areas needed for installing them, their self-assemble kits have any devices. In many cases, the fan, which will have its own lighting, will replace a ceiling light fixture.
Safety, The electricity have to be off to begin where the fan is usually to be installed. If the fan is replacing a light fixture, de-activate its fuse or circuit breaker along with flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder through the installation; tend not to lean or enter into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is required, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if required
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the light fixture in the ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws in the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections to this fixture are cold (the exam light will continue to be off). Cut the wires, leaving 3-5″ of tail in order to connect these to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one and a white one. Tip: also look into the firmness of the electrical box inside ceiling. If it can be not solidly attached to the ceiling, add two extra screws to its top side, that might require drilling two holes inside box on their behalf. The ceiling fan is heavier than the light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires inside junction box cleanly, install the mounting bracket on the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor and a blue or off-color one for your lights to become attached below it. Overlap the stripped ends of such two wires (motor and lights) together using the stripped end of the black ceiling wire inside box, and twist connect them together using the wire nut provided. Connect the white assembly wire on the white ceiling wire exactly the same way.
Then, to hold these connections from loosening even though the fan is working, tape the wide lower ends of such nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) on the electrical box in the event the box is additionally grounded with a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask a professional relating to this green wire connection. Some will say to leave it be, i.e., do nothing at all by using it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends of the mounting bracket using the small screws provided. It covers/hides the edges of the motor and also the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets using the screws and washers provided. Then mount the blades on the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to hold them separate in the rest of the kit hardware.
Tip: to hold the motor from becoming too off-level in this step, install the blades one at a time opposite to one another in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just beneath the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided in the event the lighting assembly is just not wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on using the wall switch, even though the fan itself is controlled by the pull-chain switch only, initially set inside off position. Note: The ceiling fan has a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.
