Bamboo Ceiling Fans – The flush-style ceiling fan is mounted snugly alongside a set horizontal fairly low ceiling where it is taken care of, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of room being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the tools and possible other regions required for installing them, their self-assemble kits have any devices. In many cases, the fan, that may have its own lighting, will replace a ceiling light fixture.
Safety, The electricity should be off at the site where the fan will be installed. If the fan is replacing a light fixture, power down its fuse or circuit breaker in addition to flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; do not lean or end up in a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if required
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the light fixture from your ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws from your electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections for this fixture are cold (the exam light will remain off). Cut the wires, leaving 3-5″ of tail for connecting these to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one and a white one. Tip: also check the firmness in the electrical box inside ceiling. If it is not solidly coupled to the ceiling, add two extra screws to its top side, that might require drilling two holes inside box for the children. The ceiling fan is heavier compared to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires inside junction box cleanly, install the mounting bracket for the box with the two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor and a blue or off-color one for that lights to get attached below it. Overlap the stripped ends of such two wires (motor and lights) together with the stripped end in the black ceiling wire inside box, and twist connect them together with the wire nut provided. Connect the white assembly wire for the white ceiling wire much the same way.
Then, to hold these connections from loosening as the fan is working, tape the wide lower ends of such nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) for the electrical box if the box is additionally grounded with a third bare or green wire. Otherwise, if the electrical box in not grounded, ask a specialist relating to this green wire connection. Some will say to leave it be, i.e., do nothing from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends in the mounting bracket with the small screws provided. It covers/hides the edges in the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets with the screws and washers provided. Then mount the blades for the bottom side of fan motor with the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to hold them separate from your rest in the kit hardware.
Tip: to hold the motor from becoming too off-level with this step, install the blades one by one opposite to each other in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just under the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided if the lighting assembly isn’t wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on with the wall switch, as the fan itself is controlled from the pull-chain switch only, initially set inside off position. Note: The ceiling fan carries a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.