Air Cool Brookhurst 52 In Oil Rubbed Bronze Switch Cap 549742037 pertaining to sizing 1000 X 1000Ceiling Fan Light Cap – The flush-style ceiling fan is mounted snugly alongside a flat horizontal fairly low ceiling where it can be out of the way, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the room size being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the instruments and possible other areas necessary for installing them, their self-assemble kits feature everything else. In many cases, the fan, that may have its lighting, will replace a ceiling light fixture.
Safety, The electricity has to be off at the site where the fan will be installed. If the fan is replacing a light fixture, de-activate its fuse or circuit breaker together with flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; do not lean or enter a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if needed
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the light fixture in the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws in the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to this fixture are cold (quality light will continue to be off). Cut the wires, leaving 3-5″ of tail for connecting these to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one along with a white one. Tip: also look at the firmness from the electrical box within the ceiling. If it can be not solidly connected to the ceiling, add two extra screws to its top side, that might require drilling two holes within the box for the kids. The ceiling fan is heavier as opposed to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires within the junction box cleanly, install the mounting bracket for the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger in to the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor along with a blue or off-color one for your lights to become attached below it. Overlap the stripped ends of those two wires (motor and lights) together with all the stripped end from the black ceiling wire within the box, and twist connect them together with all the wire nut provided. Connect the white assembly wire for the white ceiling wire much the same way.
Then, to keep these connections from loosening while the fan is working, tape the wide lower ends of those nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) for the electrical box when the box is additionally grounded which has a third bare or green wire. Otherwise, when the electrical box in not grounded, ask an experienced relating to this green wire connection. Some will say to let it rest be, i.e., relax from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends from the mounting bracket with all the small screws provided. It covers/hides the sides from the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets with all the screws and washers provided. Then mount the blades for the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to keep them separate in the rest from the kit hardware.
Tip: to keep the motor from becoming too off-level with this step, install the blades one by one opposite to one another first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just beneath the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided when the lighting assembly just isn’t wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on with all the wall switch, while the fan itself is controlled by the pull-chain switch only, initially set within the off position. Note: The ceiling fan features a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.
