Ceiling Fan Reverse Switch Wiring Diagram Wiring Diagram Read with sizing 1024 X 1024Reverse Ceiling Fan – Two reasons to purchase a ceiling fan, cooling and heating. If you live in a cold climate, fans can push warm air gathered at the ceiling back down. Ceiling fans could be simple to install in case you have some mechanical aptitude. Current ceiling fans come with remote-controls to vary speed and adjust lighting. If your room already has a fitting in the ceiling, your fitting probably has one hot or feed wire planning to it, the neutral white as well as the bonding green or copper. Essentially this is the three-wire system. Many new construction homes have four wires available, one for the light and one for the fan motor control as well as the neutral and ground. If you simply have one Hot wire feeding the ceiling junction box, the remote-control fans will continue to work along with your application. Additionally some remote-controlled fans use wall controller which sends its signal to the fan like a TV remote. It just appears like a wall control unit. If you only need the electricity wire on your remote-controlled fan, please cap off of the fourth wire which you will not want to work with. This needs to be shown inside your directions that came with the fan assembly.
Once you’ve got acquired an admirer that suits you, build it according to the instructions given. Some fans can be a little more complex, ask a pal to help if necessary. It is best to help it become assembled correctly, using a ceiling fan blade thud you on the pinnacle could be annoying. Once you’ve got the pre-assembly completed, you can now prepare the ceiling junction box. Of course I know you’ve got already made sure the electricity to the ceiling box is powered down with out one can possibly energize it accidentally. Once you’ve got carried this out, you must find three wires in the J-box. A copper or green wire for bonding. A white wire for the neutral plus a red or black wire for the power. If your junction box has a fourth wire, this could be build to get a wall controlled fan switch that is great and allows you to work with a non-remote wall controller. I should mention that some all fans come with a wall controllers designed as remotes so you shouldn’t be confused as these all use the singular feed inside your ceiling junction box.
A word about weight, not yours but a word in regards to the size your fan. If you’ve got a substantial fan and its weighted near 12 pounds or even more, you need a special junction box that can secure the excess weight. I would recommend you ask someone who knows about these heavier fans if that’s what you’re planning to install. Most fans are lighter and could be installed in most junction boxes without modifications.
Now we should get up there, the fan that’s. Many fans come with a Hanger the same shape as a U. Install this hanger on your box, the screws needs to be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you’ve got the hanger installed, get your fan motor without the blades installed and hang up it on the hanger. This allows you the electrician to attach the wires without struggling to juggle the motor and wire it at the same time. Connect the bonding wire to the chassis as noted in the instructions. Next connect the white neutral wire, now the black wire. Swing the fan into place while using the parts provided. Some have brackets, some work with a metal plate although some use preformed mounting bases. Use your instructions and you’ll have an admirer right away. Smaller fans may need one to pre-assemble your blades before hanging the fan. I always found installing the motor first then installing the blades last is less difficult. It does require however, one to work above your head to get the blades attached.
Once you’ve got the fan hanging, the blades installed and everything tightened you can now step off of the ladder, breathe deeply, then install the wall controller as provided. These all vary in design nonetheless they all follow similar procedures. Remember, you’ll have a line and load situation here. This means, the road side is the pair of wires the feed in the switch box from the panel even though the Load side is planning to your fan. This is critical so be sure you view the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next perform the Line (incoming) side next: Bond or ground should already be constructed to the new controller. Next wire your white neutral to the controllers neutral for the Line side. You may have already wired your neutrals together as outlined by your instructions. Now wire your Hot or Power wire to the Line side of the controller. If you’ve got the fourth wire in that room, cap rid of it or use it for the motor control and connect it accordingly to your directions. Red to Red is usually the case here. Once completed, be some Iced Tea and enjoy a new fan.
