Hunter Bennett 52 In Led Low Profile Brushed Nickel Indoor Ceiling with regard to sizing 1000 X 1000Edison Ceiling Fan – The flush-style ceiling fan is mounted snugly next to a set horizontal fairly low ceiling where it can be off the beaten track, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the various tools and possible other regions needed for installing them, their self-assemble kits have anything else. In many cases, the fan, that may have its own lighting, will replace a ceiling fitting.
Safety, The electricity must be off at the site the place that the fan is to be installed. If the fan is replacing a fitting, de-activate its fuse or circuit breaker in addition to flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder through the installation; do not lean or get into a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if necessary
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the fitting from your ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws from your electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to this particular fixture are cold (the exam light will remain off). Cut the wires, leaving 3-5″ of tail to get in touch these to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one along with a white one. Tip: also check the firmness from the electrical box inside ceiling. If it can be not solidly attached to the ceiling, add two extra screws to its top side, that might require drilling two holes inside box for the children. The ceiling fan is heavier compared to fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires inside junction box cleanly, install the mounting bracket towards the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger to the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor along with a blue or off-color one to the lights to be attached below it. Overlap the stripped ends of such two wires (motor and lights) together with all the stripped end from the black ceiling wire inside box, and twist connect them together with all the wire nut provided. Connect the white assembly wire towards the white ceiling wire exactly the same.
Then, to keep these connections from loosening whilst the fan is working, tape the wide lower ends of such nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) towards the electrical box when the box is also grounded having a third bare or green wire. Otherwise, when the electrical box in not grounded, ask an experienced about this green wire connection. Some will say to let it rest be, i.e., relax with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends from the mounting bracket with all the small screws provided. It covers/hides the edges from the motor along with the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets with all the screws and washers provided. Then mount the blades towards the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to keep them separate from your rest from the kit hardware.
Tip: to keep the motor from becoming too off-level during this step, install the blades one at a time opposite to one another in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just underneath the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided when the lighting assembly just isn’t wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on with all the wall switch, whilst the fan itself is controlled by the pull-chain switch only, initially set inside off position. Note: The ceiling fan features a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.
