Chic Ceiling Fans – The flush-style ceiling fan is mounted snugly beside a designated horizontal fairly low ceiling where it is taken care of, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of the room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the tools and possible other parts necessary for installing them, their self-assemble kits include anything else. In many cases, the fan, that will have its own lighting, will replace a ceiling light fixture.
Safety, The electricity has to be off once your there the place that the fan is usually to be installed. If the fan is replacing a light fixture, power down its fuse or circuit breaker in addition to flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; tend not to lean or end up in a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if required
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the light fixture from your ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws from your electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections for this fixture are cold (test light will continue to be off). Cut the wires, leaving 3-5″ of tail allowing you to connect these to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one as well as a white one. Tip: also confirm the firmness from the electrical box inside ceiling. If it is not solidly attached to the ceiling, add two extra screws to its top side, which might require drilling two holes inside box for the kids. The ceiling fan is heavier as opposed to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires inside junction box cleanly, install the mounting bracket on the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger to the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor as well as a blue or off-color one to the lights to become attached below it. Overlap the stripped ends of the two wires (motor and lights) together with all the stripped end from the black ceiling wire inside box, and twist connect them together with all the wire nut provided. Connect the white assembly wire on the white ceiling wire much the same way.
Then, to help keep these connections from loosening as the fan is working, tape the wide lower ends of the nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) on the electrical box if the box is additionally grounded using a third bare or green wire. Otherwise, if the electrical box in not grounded, ask a specialist concerning this green wire connection. Some will say to let it rest be, i.e., relax by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends from the mounting bracket with all the small screws provided. It covers/hides the sides from the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets with all the screws and washers provided. Then mount the blades on the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to help keep them separate from your rest from the kit hardware.
Tip: to help keep the motor from becoming too off-level with this step, install the blades one at a time opposite to one another to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just beneath the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided if the lighting assembly just isn’t wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on with all the wall switch, as the fan itself is controlled by the pull-chain switch only, initially set inside off position. Note: The ceiling fan has a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.