Harbor Breeze Double Ceiling Fan – The flush-style ceiling fan is mounted snugly alongside an appartment horizontal fairly low ceiling where it can be dealt with, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of the room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the tools and possible the rest necessary for installing them, their self-assemble kits feature everything else. In many cases, the fan, which will have its very own lighting, will replace a ceiling permanent fixture.
Safety, The electricity has to be off at the site in which the fan shall be installed. If the fan is replacing a permanent fixture, power down its fuse or circuit breaker in addition to flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder through the installation; don’t lean or enter into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is required, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if required
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the permanent fixture from your ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws from your electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to the fixture are cold (the exam light will remain off). Cut the wires, leaving 3-5″ of tail to get in touch these phones the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one along with a white one. Tip: also check the firmness of the electrical box within the ceiling. If it can be not solidly connected to the ceiling, add two extra screws to its top side, which can require drilling two holes within the box for the children. The ceiling fan is heavier than the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires within the junction box cleanly, install the mounting bracket on the box with the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor along with a blue or off-color one for the lights being attached below it. Overlap the stripped ends of those two wires (motor and lights) together with the stripped end of the black ceiling wire within the box, and twist connect them together with the wire nut provided. Connect the white assembly wire on the white ceiling wire much the same way.
Then, to hold these connections from loosening even though the fan is working, tape the wide lower ends of those nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) on the electrical box if the box is also grounded which has a third bare or green wire. Otherwise, if the electrical box in not grounded, ask an experienced relating to this green wire connection. Some will say to leave it be, i.e., do nothing at all by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends of the mounting bracket with the small screws provided. It covers/hides the edges of the motor along with the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets with the screws and washers provided. Then mount the blades on the bottom side of fan motor with the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to hold them separate from your rest of the kit hardware.
Tip: to hold the motor from becoming too off-level within this step, install the blades one at a time opposite together to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just under the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided if the lighting assembly is not wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on with the wall switch, even though the fan itself is controlled by the pull-chain switch only, initially set within the off position. Note: The ceiling fan features a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.