Bulbs Ideas

Light Covers For Ceiling Fans

Ceiling Fan Light Covers with proportions 1152 X 864

Ceiling Fan Light Covers with proportions 1152 X 864

Light Covers For Ceiling Fans – The flush-style ceiling fan is mounted snugly next to a flat horizontal fairly low ceiling where it is off the beaten track, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, depending on the size of the room being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the equipment and possible other regions essential for installing them, their self-assemble kits come with anything else. In many cases, the fan, that can have its very own lighting, will replace a ceiling light fixture.

Safety, The electricity must be off once your there in which the fan is to be installed. If the fan is replacing a light fixture, turn off its fuse or circuit breaker together with flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; don’t lean or get into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if required

Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the light fixture through the ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws through the electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections for this fixture are cold (quality light will always be off). Cut the wires, leaving 3-5″ of tail to get in touch these to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one plus a white one. Tip: also look at the firmness of the electrical box in the ceiling. If it is not solidly attached to the ceiling, add two extra screws to its top side, which could require drilling two holes in the box for them. The ceiling fan is heavier compared to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires in the junction box cleanly, install the mounting bracket for the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor plus a blue or off-color one for that lights to be attached below it. Overlap the stripped ends of the two wires (motor and lights) together with all the stripped end of the black ceiling wire in the box, and twist connect them together with all the wire nut provided. Connect the white assembly wire for the white ceiling wire exactly the same.


Then, to help keep these connections from loosening while the fan is working, tape the wide lower ends of the nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) for the electrical box if your box can also be grounded having a third bare or green wire. Otherwise, if your electrical box in not grounded, ask a specialist concerning this green wire connection. Some will say to let it rest be, i.e., relax with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends of the mounting bracket with all the small screws provided. It covers/hides the edges of the motor and also the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets with all the screws and washers provided. Then mount the blades for the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to help keep them separate through the rest of the kit hardware.

Tip: to help keep the motor from becoming too off-level during this step, install the blades one-by-one opposite to one another to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just underneath the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided if your lighting assembly isn’t wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on with all the wall switch, while the fan itself is controlled with the pull-chain switch only, initially set in the off position. Note: The ceiling fan features a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.

Exit mobile version