Casablanca Ceiling Fan Light Kit – Two top reasons to install a ceiling fan, heating and cooling. If you live in a cold climate, fans can push warm air gathered near the ceiling back off. Ceiling fans might be easy to install when you have some mechanical aptitude. Current ceiling fans include remote-controls to vary speed and adjust lighting. If your room already carries a permanent fixture inside the ceiling, your permanent fixture probably has one hot or feed wire gonna it, the neutral white and the bonding green or copper. Essentially it is a three-wire system. Many new construction homes have four wires available, one to the light the other to the fan motor control and the neutral and ground. If you simply have one Hot wire feeding the ceiling junction box, the remote-control fans will continue to work with your application. Additionally some remote-controlled fans use wall controller which sends its signal to the fan just like a TV remote. It just looks like a wall control unit. If you just have the ability wire for the remote-controlled fan, please cap off of the fourth wire which you will not want to work with. This should be shown with your directions that was included with the fan assembly.
Once you have acquired a lover that suits you, build it according to the instructions given. Some fans can be a much more complex, ask a pal to help if you need to. It is best to makes it assembled correctly, creating a ceiling fan blade thud yourself the pinnacle might be annoying. Once you have the pre-assembly completed, you can now prepare the ceiling junction box. Of course I know you have already made sure the ability to the ceiling box is powered down and no one can possibly energize it accidentally. Once you have performed this, you need to find three wires inside the J-box. A copper or green wire for bonding. A white wire to the neutral and a red or black wire to the power. If your junction box carries a fourth wire, this may be create for any wall controlled fan switch that is great and allows you to work with a non-remote wall controller. I should mention that some all fans include a wall controllers designed as remotes so you shouldn’t be confused as these all use the singular feed with your ceiling junction box.
A word about weight, not yours but a word regarding the height and width of your fan. If you have a sizable fan as well as weighted near 12 pounds or higher, you might need a special junction box that will secure the additional weight. I would recommend i hear you ask somebody who knows about these heavier fans you might need what you’re gonna install. Most fans are lighter and might be installed in most junction boxes without modifications.
Now let’s get it there, the fan that’s. Many fans include a Hanger the same shape as a U. Install this hanger on to your box, the screws should be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you have the hanger installed, get your fan motor with no blades installed and hang it around the hanger. This allows you the electrician to connect the wires without struggling to juggle the motor and wire it as well. Connect the bonding wire to the chassis as noted inside the instructions. Next connect the white neutral wire, and after this the black wire. Swing the fan into place while using the parts provided. Some have brackets, some use a metal plate and some use preformed mounting bases. Use your instructions and you will have a lover very quickly. Smaller fans might require you to pre-assemble your blades before hanging the fan. I always found installing the motor first and after that installing the blades last is less difficult. It does require however, you to work above your brain to get the blades attached.
Once you have the fan hanging, the blades installed and everything tightened you can now step off of the ladder, relax, then install the wall controller as provided. These all vary in design nonetheless they all follow similar procedures. Remember, you will have a line and load situation here. This means, the fishing line side may be the list of wires the feed into the switch box in the panel while the Load side is gonna your fan. This is critical so be sure to see the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next perform Line (incoming) side next: Bond or ground should already be constructed to the new controller. Next wire your white neutral to the controllers neutral to the Line side. You may have already wired your neutrals together according to your instructions. Now wire your Hot or Power wire to the Line side of your controller. If you have the fourth wire in that room, cap them back or use it to the motor control and connect it accordingly in your directions. Red to Red is truly the case here. Once completed, make yourself some Iced Tea and revel in a new fan.