Rustic Modern Ceiling Fans – The flush-style ceiling fan is mounted snugly next to a set horizontal fairly low ceiling where it’s taken care of, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, depending on the size of room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the various tools and possible other areas required for installing them, their self-assemble kits include anything else. In many cases, the fan, which will have its lighting, will replace a ceiling light fixture.
Safety, The electricity have to be off once your there the place that the fan is to be installed. If the fan is replacing a light fixture, turn off its fuse or circuit breaker in addition to flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; usually do not lean or get into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if needed
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the light fixture from your ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws from your electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to this fixture are cold (the test light will continue to be off). Cut the wires, leaving 3-5″ of tail to get in touch these to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one and a white one. Tip: also confirm the firmness with the electrical box inside ceiling. If it’s not solidly attached to the ceiling, add two extra screws to its top side, which can require drilling two holes inside box for the children. The ceiling fan is heavier than the light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires inside junction box cleanly, install the mounting bracket towards the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in to the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor and a blue or off-color one for the lights to become attached below it. Overlap the stripped ends of such two wires (motor and lights) together while using stripped end with the black ceiling wire inside box, and twist connect them together while using wire nut provided. Connect the white assembly wire towards the white ceiling wire much the same way.
Then, to help keep these connections from loosening while the fan is working, tape the wide lower ends of such nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) towards the electrical box in the event the box can be grounded with a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask an expert concerning this green wire connection. Some will say to leave it be, i.e., relax by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends with the mounting bracket while using small screws provided. It covers/hides the sides with the motor along with the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets while using screws and washers provided. Then mount the blades towards the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to help keep them separate from your rest with the kit hardware.
Tip: to help keep the motor from becoming too off-level during this step, install the blades one-by-one opposite together first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just under the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided in the event the lighting assembly just isn’t wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on while using wall switch, while the fan itself is controlled from the pull-chain switch only, initially set inside off position. Note: The ceiling fan includes a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.