Sea Gull Lighting Roman Bronze Metal Angle Mount Ceiling Fan within dimensions 900 X 900Angle Mount Ceiling Fan – The flush-style ceiling fan is mounted snugly next to a set horizontal fairly low ceiling where it can be off the beaten track, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, depending on the size of room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the equipment and possible other regions needed for installing them, their self-assemble kits come with anything else. In many cases, the fan, that can have a unique lighting, will replace a ceiling fitting.
Safety, The electricity have to be off to begin the place that the fan is usually to be installed. If the fan is replacing a fitting, turn off its fuse or circuit breaker together with flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; do not lean or get into a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if needed
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the fitting through the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws through the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections to the fixture are cold (the exam light will continue to be off). Cut the wires, leaving 3-5″ of tail in order to connect them to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one along with a white one. Tip: also check the firmness of the electrical box inside ceiling. If it can be not solidly coupled to the ceiling, add two extra screws to its top side, which could require drilling two holes inside box on their behalf. The ceiling fan is heavier as opposed to fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires inside junction box cleanly, install the mounting bracket towards the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger in to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor along with a blue or off-color one for that lights to be attached below it. Overlap the stripped ends of the two wires (motor and lights) together using the stripped end of the black ceiling wire inside box, and twist connect them together using the wire nut provided. Connect the white assembly wire towards the white ceiling wire exactly the same way.
Then, to keep these connections from loosening as the fan is working, tape the wide lower ends of the nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) towards the electrical box in the event the box is additionally grounded with a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask a specialist relating to this green wire connection. Some will say to leave it be, i.e., do nothing with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends of the mounting bracket using the small screws provided. It covers/hides the edges of the motor along with the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets using the screws and washers provided. Then mount the blades towards the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to keep them separate through the rest of the kit hardware.
Tip: to keep the motor from becoming too off-level in this step, install the blades individually opposite to one another in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just below the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided in the event the lighting assembly is not wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on using the wall switch, as the fan itself is controlled through the pull-chain switch only, initially set inside off position. Note: The ceiling fan includes a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.
