Avion for sizing 1200 X 1140Avion Ceiling Fan – The flush-style ceiling fan is mounted snugly next to a designated horizontal fairly low ceiling where it can be off the beaten track, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, depending on the size of the room being fitted, and can cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the instruments and possible other regions needed for installing them, their self-assemble kits feature any devices. In many cases, the fan, that may have its lighting, will replace a ceiling permanent fixture.
Safety, The electricity has to be off at the site in which the fan is to be installed. If the fan is replacing a permanent fixture, turn off its fuse or circuit breaker in addition to flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; do not lean or enter a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if necessary
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the permanent fixture through the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws through the electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections for this fixture are cold (the exam light will continue to be off). Cut the wires, leaving 3-5″ of tail in order to connect these phones the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one and a white one. Tip: also check the firmness in the electrical box inside the ceiling. If it can be not solidly attached to the ceiling, add two extra screws to its top side, which could require drilling two holes inside the box for the kids. The ceiling fan is heavier compared to the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires inside the junction box cleanly, install the mounting bracket on the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger to the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor and a blue or off-color one for the lights to become attached below it. Overlap the stripped ends of these two wires (motor and lights) together while using stripped end in the black ceiling wire inside the box, and twist connect them together while using wire nut provided. Connect the white assembly wire on the white ceiling wire the same way.
Then, to keep these connections from loosening even though the fan is working, tape the wide lower ends of these nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) on the electrical box if the box is additionally grounded using a third bare or green wire. Otherwise, if the electrical box in not grounded, ask a professional about it green wire connection. Some will say to let it rest be, i.e., relax with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends in the mounting bracket while using small screws provided. It covers/hides the edges in the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets while using screws and washers provided. Then mount the blades on the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to keep them separate through the rest in the kit hardware.
Tip: to keep the motor from becoming too off-level in this step, install the blades one by one opposite to each other to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just under the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided if the lighting assembly is just not wanted without any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on while using wall switch, even though the fan itself is controlled with the pull-chain switch only, initially set inside the off position. Note: The ceiling fan has a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.
