Gale Series 14 In Textured Bronze Indoor Halogen Double Headed pertaining to dimensions 1000 X 1000Double Ceiling Fan – The flush-style ceiling fan is mounted snugly alongside an appartment horizontal fairly low ceiling where it is taken care of, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the instruments and possible the rest needed for installing them, their self-assemble kits feature the rest. In many cases, the fan, which will have its very own lighting, will replace a ceiling fitting.
Safety, The electricity have to be off once your there the location where the fan shall be installed. If the fan is replacing a fitting, de-activate its fuse or circuit breaker together with flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; usually do not lean or enter into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is required, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if needed
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the fitting from your ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws from your electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to this particular fixture are cold (the exam light will stay off). Cut the wires, leaving 3-5″ of tail to get in touch these phones the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one plus a white one. Tip: also check the firmness from the electrical box in the ceiling. If it is not solidly connected to the ceiling, add two extra screws to its top side, which can require drilling two holes in the box for the kids. The ceiling fan is heavier compared to fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires in the junction box cleanly, install the mounting bracket for the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in to the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor plus a blue or off-color one for that lights to become attached below it. Overlap the stripped ends of the two wires (motor and lights) together using the stripped end from the black ceiling wire in the box, and twist connect them together using the wire nut provided. Connect the white assembly wire for the white ceiling wire exactly the same.
Then, to maintain these connections from loosening whilst the fan is working, tape the wide lower ends of the nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) for the electrical box in the event the box can be grounded which has a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask a professional about this green wire connection. Some will say to leave it be, i.e., relax with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends from the mounting bracket using the small screws provided. It covers/hides the edges from the motor and the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets using the screws and washers provided. Then mount the blades for the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to maintain them separate from your rest from the kit hardware.
Tip: to maintain the motor from becoming too off-level with this step, install the blades one-by-one opposite to each other first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just below the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided in the event the lighting assembly just isn’t wanted without any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on using the wall switch, whilst the fan itself is controlled by the pull-chain switch only, initially set in the off position. Note: The ceiling fan carries a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.
