Hunter Channelside 52 In Led Indooroutdoor Noble Bronze Ceiling regarding sizing 1000 X 1000Hunter Remote Control Ceiling Fans With Lights – The flush-style ceiling fan is mounted snugly close to a designated horizontal fairly low ceiling where it’s taken care of, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the room size being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the instruments and possible other parts needed for installing them, their self-assemble kits have anything else. In many cases, the fan, which will have a unique lighting, will replace a ceiling light fixture.
Safety, The electricity must be off at the site the location where the fan is to be installed. If the fan is replacing a light fixture, power down its fuse or circuit breaker together with flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; tend not to lean or end up in a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if needed
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the light fixture from the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws from the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to the fixture are cold (test light will stay off). Cut the wires, leaving 3-5″ of tail for connecting these phones the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one as well as a white one. Tip: also check the firmness with the electrical box within the ceiling. If it’s not solidly coupled to the ceiling, add two extra screws to its top side, which might require drilling two holes within the box for the kids. The ceiling fan is heavier than the light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires within the junction box cleanly, install the mounting bracket to the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger into the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor as well as a blue or off-color one for the lights being attached below it. Overlap the stripped ends of the two wires (motor and lights) together using the stripped end with the black ceiling wire within the box, and twist connect them together using the wire nut provided. Connect the white assembly wire to the white ceiling wire exactly the same.
Then, to maintain these connections from loosening while the fan is working, tape the wide lower ends of the nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) to the electrical box if the box is additionally grounded using a third bare or green wire. Otherwise, if the electrical box in not grounded, ask a professional about it green wire connection. Some will say to get forced out be, i.e., do nothing at all by using it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends with the mounting bracket using the small screws provided. It covers/hides the edges with the motor and also the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets using the screws and washers provided. Then mount the blades to the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to maintain them separate from the rest with the kit hardware.
Tip: to maintain the motor from becoming too off-level with this step, install the blades individually opposite together to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just below the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided if the lighting assembly is not wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on using the wall switch, while the fan itself is controlled through the pull-chain switch only, initially set within the off position. Note: The ceiling fan features a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.
