Ceiling Fan Swag Kit Photo Album Home Design Ideas intended for proportions 1024 X 768Ceiling Fan Swag Kit – The flush-style ceiling fan is mounted snugly beside a designated horizontal fairly low ceiling where it can be out of the way, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of the room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the various tools and possible other regions needed for installing them, their self-assemble kits feature everything else. In many cases, the fan, which will have its lighting, will replace a ceiling permanent fixture.
Safety, The electricity should be off once your there the location where the fan is usually to be installed. If the fan is replacing a permanent fixture, shut down its fuse or circuit breaker along with flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; tend not to lean or end up in a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, as appropriate
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the permanent fixture from the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws from the electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to this fixture are cold (the test light will always be off). Cut the wires, leaving 3-5″ of tail to get in touch these to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one plus a white one. Tip: also look into the firmness in the electrical box in the ceiling. If it can be not solidly coupled to the ceiling, add two extra screws to its top side, which might require drilling two holes in the box for the kids. The ceiling fan is heavier than the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires in the junction box cleanly, install the mounting bracket on the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger to the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor plus a blue or off-color one for your lights to get attached below it. Overlap the stripped ends of those two wires (motor and lights) together using the stripped end in the black ceiling wire in the box, and twist connect them together using the wire nut provided. Connect the white assembly wire on the white ceiling wire much the same way.
Then, to maintain these connections from loosening as the fan is working, tape the wide lower ends of those nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) on the electrical box if the box is also grounded using a third bare or green wire. Otherwise, if the electrical box in not grounded, ask an expert concerning this green wire connection. Some will say to get forced out be, i.e., do nothing by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends in the mounting bracket using the small screws provided. It covers/hides the sides in the motor along with the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets using the screws and washers provided. Then mount the blades on the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to maintain them separate from the rest in the kit hardware.
Tip: to maintain the motor from becoming too off-level with this step, install the blades individually opposite to each other to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just below the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided if the lighting assembly is not wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on using the wall switch, as the fan itself is controlled from the pull-chain switch only, initially set in the off position. Note: The ceiling fan carries a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.
