Antique Reproduction Ceiling Fans – The flush-style ceiling fan is mounted snugly beside a flat horizontal fairly low ceiling where it’s dealt with, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of the room being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the tools and possible other regions required for installing them, their self-assemble kits come with everything else. In many cases, the fan, which will have its very own lighting, will replace a ceiling light fixture.
Safety, The electricity has to be off at the site the location where the fan is to be installed. If the fan is replacing a light fixture, turn off its fuse or circuit breaker together with flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; usually do not lean or end up in a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if needed
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the light fixture in the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws in the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections for this fixture are cold (the test light will continue to be off). Cut the wires, leaving 3-5″ of tail in order to connect them to the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one as well as a white one. Tip: also look into the firmness of the electrical box within the ceiling. If it’s not solidly coupled to the ceiling, add two extra screws to its top side, which could require drilling two holes within the box for them. The ceiling fan is heavier compared to the light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires within the junction box cleanly, install the mounting bracket to the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger in the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor as well as a blue or off-color one for that lights to become attached below it. Overlap the stripped ends of such two wires (motor and lights) together with all the stripped end of the black ceiling wire within the box, and twist connect them together with all the wire nut provided. Connect the white assembly wire to the white ceiling wire the same way.
Then, to help keep these connections from loosening while the fan is working, tape the wide lower ends of such nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) to the electrical box when the box can be grounded which has a third bare or green wire. Otherwise, when the electrical box in not grounded, ask an experienced about it green wire connection. Some will say to leave it be, i.e., do nothing with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends of the mounting bracket with all the small screws provided. It covers/hides the sides of the motor and the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets with all the screws and washers provided. Then mount the blades to the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to help keep them separate in the rest of the kit hardware.
Tip: to help keep the motor from becoming too off-level during this step, install the blades one by one opposite together to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just under the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided when the lighting assembly isn’t wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on with all the wall switch, while the fan itself is controlled by the pull-chain switch only, initially set within the off position. Note: The ceiling fan has a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.