Dining Room Ceiling Fan – Two good reasons to install a ceiling fan, air conditioning. If you live in a cold climate, fans can push hot air gathered nearby the ceiling back off. Ceiling fans can be an easy task to install for those who have some mechanical aptitude. Current ceiling fans come with remote-controls to vary speed and adjust lighting. If your room already features a light fixture inside ceiling, your light fixture probably has one hot or feed wire going to it, the neutral white and the bonding green or copper. Essentially it is a three-wire system. Many new construction homes have four wires available, one for the light then one for the fan motor control and the neutral and ground. If you have only one Hot wire feeding the ceiling junction box, the remote-control fans works using your application. Additionally some remote-controlled fans use wall controller which sends its signal to the fan like a TV remote. It just looks like a wall control unit. If you really need the power wire for your remote-controlled fan, please cap from the fourth wire which you will n’t need to make use of. This needs to be shown with your directions that had the fan assembly.
Once you might have acquired a lover you want, build it according to the instructions given. Some fans can be a bit more complex, ask a friend to help you if required. It is best to makes it assembled correctly, developing a ceiling fan blade thud your self on the top can be annoying. Once you might have the pre-assembly completed, it’s simple to prepare the ceiling junction box. Of course I know you might have already made sure the power to the ceiling box is turned off with out you can energize it accidentally. Once you might have done this, you should find three wires inside J-box. A copper or green wire for bonding. A white wire for the neutral along with a red or black wire for the power. If your junction box features a fourth wire, this would be build for any wall controlled fan switch which is great and allows you to make use of a non-remote wall controller. I should mention that some all fans come with a wall controllers designed as remotes so don’t be confused as these all assist the singular feed with your ceiling junction box.
A word about weight, not yours but anything about the sized your fan. If you might have a big fan and its weighted near 12 pounds or more, you need a special junction box that could offer the more weight. I would recommend you may ask somebody that knows about these heavier fans if that is what you will be going to install. Most fans are lighter and can be set up in most junction boxes without modifications.
Now why don’t we get up there, the fan that’s. Many fans come with a Hanger in the shape of a U. Install this hanger onto your box, the screws needs to be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you might have the hanger installed, pick up your fan motor minus the blades installed and hang up it around the hanger. This allows you the electrician to get together the wires without struggling to juggle the motor and wire it at the same time. Connect the bonding wire to the chassis as noted inside instructions. Next connect the white neutral wire, and after this the black wire. Swing the fan into place using the parts provided. Some have brackets, some use a metal plate while others use preformed mounting bases. Use your instructions you may have a lover in no time. Smaller fans may need you to definitely pre-assemble your blades before hanging the fan. I always found installing the motor first then installing the blades last is less difficult. It does require however, you to definitely work above your mind to get the blades attached.
Once you might have the fan hanging, the blades installed and everything tightened it’s simple to step from the ladder, take a deep breath, then install the wall controller as provided. These all vary in design but they all follow similar procedures. Remember, you will find a line and load situation here. This means, the road side may be the list of wires the feed into the switch box from your panel as the Load side is going to your fan. This is critical so be sure you understand the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next do the Line (incoming) side next: Bond or ground should already be constructed to the new controller. Next wire your white neutral to the controllers neutral for the Line side. You may have already wired your neutrals together according to your instructions. Now wire your Hot or Power wire to the Line side of your respective controller. If you might have the fourth wire in there, cap it well or use it for the motor control and connect it accordingly in your directions. Red to Red is usually the case here. Once completed, be some Iced Tea and luxuriate in your fan.