Low Profile Ceiling Fan With Remote – Two good reasons to purchase a ceiling fan, air conditioning. If you live in a very cold climate, fans can push warm air gathered at the ceiling back off. Ceiling fans might be simple to install in case you have some mechanical aptitude. Current ceiling fans come with remote-controls to vary speed and adjust lighting. If your room already has a light fixture within the ceiling, your light fixture probably has one hot or feed wire planning to it, the neutral white and also the bonding green or copper. Essentially it is a three-wire system. Many new construction homes have four wires available, one to the light and one to the fan motor control and also the neutral and ground. If you have only one Hot wire feeding the ceiling junction box, the remote-control fans work together with your application. Additionally some remote-controlled fans use wall controller which sends its signal for the fan like a TV remote. It just seems like a wall control unit. If you only need the energy wire to your remote-controlled fan, please cap from the fourth wire which you will not need to make use of. This needs to be shown in your directions that had the fan assembly.
Once you’ve acquired a fan that suits you, put it together according for the instructions given. Some fans are a bit more complex, ask a buddy to assist if need be. It is best to makes it assembled correctly, creating a ceiling fan blade thud your self on the head might be annoying. Once you’ve the pre-assembly completed, now you can prepare the ceiling junction box. Of course I know you’ve already ensured the energy for the ceiling box is switched off no you can energize it accidentally. Once you’ve performed this, you should find three wires within the J-box. A copper or green wire for bonding. A white wire to the neutral along with a red or black wire to the power. If your junction box has a fourth wire, this is set up for a wall controlled fan switch that’s great and allows you to make use of a non-remote wall controller. I should mention that some all fans come with a wall controllers designed as remotes so do not be confused because these all work with the singular feed in your ceiling junction box.
A word about weight, not yours but a word concerning the size of your fan. If you’ve a big fan and its particular weighted near 12 pounds or higher, you may need a special junction box that could support the excess weight. I would recommend you ask someone who knows about these heavier fans if that is what you will be planning to install. Most fans are lighter and might be positioned in most junction boxes without modifications.
Now let’s get it up there, the fan which is. Many fans come with a Hanger in the shape of a U. Install this hanger on your box, the screws needs to be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you’ve the hanger installed, pick up your fan motor without the blades installed and place it about the hanger. This allows you the electrician to connect the wires without struggling to juggle the motor and wire it at the same time. Connect the bonding wire for the chassis as noted within the instructions. Next connect the white neutral wire, and after this the black wire. Swing the fan into place while using parts provided. Some have brackets, some work with a metal plate while others use preformed mounting bases. Use your instructions and you’ll have a fan quickly. Smaller fans might require you to definitely pre-assemble your blades before hanging the fan. I always found installing the motor first after which installing the blades last is much easier. It does require however, you to definitely work above your face to obtain the blades attached.
Once you’ve the fan hanging, the blades installed and everything tightened now you can step from the ladder, relax, then install the wall controller as provided. These all vary in design however they all follow similar procedures. Remember, you will find a line and load situation here. This means, the line side will be the set of wires the feed in the switch box from your panel while the Load side is planning to your fan. This is critical so be sure to understand the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next perform Line (incoming) side next: Bond or ground should already be constructed for the new controller. Next wire your white neutral for the controllers neutral to the Line side. You may have already wired your neutrals together based on your instructions. Now wire your Hot or Power wire for the Line side of your respective controller. If you’ve the fourth wire inside, cap rid of it or use it to the motor control and connect it accordingly to your directions. Red to Red is often the case here. Once completed, get yourself some Iced Tea and revel in a new fan.