Ceiling Fan Chandelier Light Kit – The flush-style ceiling fan is mounted snugly alongside an appartment horizontal fairly low ceiling where it’s out of the way, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, according to the size of room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the tools and possible other regions necessary for installing them, their self-assemble kits come with anything else. In many cases, the fan, which will have its own lighting, will replace a ceiling fitting.
Safety, The electricity have to be off once your there the place that the fan is to be installed. If the fan is replacing a fitting, de-activate its fuse or circuit breaker in addition to flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; usually do not lean or enter into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if needed
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the fitting from the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws from the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to this particular fixture are cold (quality light will always be off). Cut the wires, leaving 3-5″ of tail to get in touch them to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one and a white one. Tip: also check the firmness in the electrical box within the ceiling. If it’s not solidly attached to the ceiling, add two extra screws to its top side, that might require drilling two holes within the box on their behalf. The ceiling fan is heavier than the fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires within the junction box cleanly, install the mounting bracket to the box with the two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger into the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor and a blue or off-color one for that lights being attached below it. Overlap the stripped ends of the two wires (motor and lights) together with the stripped end in the black ceiling wire within the box, and twist connect them together with the wire nut provided. Connect the white assembly wire to the white ceiling wire the same way.
Then, to keep these connections from loosening even though the fan is working, tape the wide lower ends of the nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) to the electrical box in the event the box can also be grounded having a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask a specialist about this green wire connection. Some will say to get forced out be, i.e., do nothing at all with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends in the mounting bracket with the small screws provided. It covers/hides the perimeters in the motor and also the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets with the screws and washers provided. Then mount the blades to the bottom side of fan motor with the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to keep them separate from the rest in the kit hardware.
Tip: to keep the motor from becoming too off-level within this step, install the blades one at a time opposite to each other in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just beneath the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided in the event the lighting assembly is not wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on with the wall switch, even though the fan itself is controlled by the pull-chain switch only, initially set within the off position. Note: The ceiling fan features a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.