Quorum Ceiling Fans – Two reasons to install a ceiling fan, cooling and heating. If you live in a very cold climate, fans can push hot air gathered near the ceiling down again. Ceiling fans might be all to easy to install in case you have some mechanical aptitude. Current ceiling fans have remote-controls to vary speed and adjust lighting. If your room already includes a light fixture within the ceiling, your light fixture probably has one hot or feed wire gonna it, the neutral white and the bonding green or copper. Essentially this is a three-wire system. Many new construction homes have four wires available, one for the light then one for the fan motor control and the neutral and ground. If you have only one Hot wire feeding the ceiling junction box, the remote-control fans work along with your application. Additionally some remote-controlled fans use wall controller which sends its signal on the fan being a TV remote. It just appears like a wall control unit. If you merely have the ability wire for your remote-controlled fan, please cap off the fourth wire which you will n’t need to work with. This ought to be shown in your directions that had the fan assembly.
Once you have acquired a lover you like, put it together according on the instructions given. Some fans can be a much more complex, ask a pal to assist if need be. It is best to help it become assembled correctly, creating a ceiling fan blade thud you on the head might be annoying. Once you have the pre-assembly completed, anyone can prepare the ceiling junction box. Of course I know you have already made sure the ability on the ceiling box is powered down with no one can energize it accidentally. Once you have done this, you should find three wires within the J-box. A copper or green wire for bonding. A white wire for the neutral as well as a red or black wire for the power. If your junction box includes a fourth wire, this is build for a wall controlled fan switch which can be great and allows you to work with a non-remote wall controller. I should mention that some all fans have a wall controllers designed as remotes so don’t be confused as these all use the singular feed in your ceiling junction box.
A word about weight, not yours but a word about the size your fan. If you have a sizable fan and its weighted near 12 pounds or even more, you will need a special junction box that could offer the more weight. I would recommend you ask somebody who knows about these heavier fans if that’s what you will be gonna install. Most fans are lighter and might be placed in most junction boxes without modifications.
Now let us get it down there, the fan that is. Many fans have a Hanger the same shape as a U. Install this hanger onto your box, the screws ought to be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you have the hanger installed, pick up your fan motor without the blades installed and hang it on the hanger. This allows you the electrician to attach the wires without struggling to juggle the motor and wire it at the same time. Connect the bonding wire on the chassis as noted within the instructions. Next connect the white neutral wire, and today the black wire. Swing the fan into place using the parts provided. Some have brackets, some make use of a metal plate although some use preformed mounting bases. Use your instructions you’ll also find a lover right away. Smaller fans might require you to pre-assemble your blades before hanging the fan. I always found installing the motor first and then installing the blades last is easier. It does require however, you to work above your mind to have the blades attached.
Once you have the fan hanging, the blades installed and everything tightened anyone can step off the ladder, breathe deeply, then install the wall controller as provided. These all vary in design but they all follow similar procedures. Remember, you will have line and load situation here. This means, the fishing line side will be the list of wires the feed in to the switch box in the panel as the Load side is gonna your fan. This is critical so be sure you comprehend the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next do the Line (incoming) side next: Bond or ground should already be composed on the new controller. Next wire your white neutral on the controllers neutral for the Line side. You may have already wired your neutrals together in accordance with your instructions. Now wire your Hot or Power wire on the Line side of the controller. If you have the fourth wire within, cap it well or use it for the motor control and connect it accordingly for a directions. Red to Red is truly the case here. Once completed, get yourself some Iced Tea and enjoy your new fan.