Circulaire Discus 3 Head Ceiling Fan In English Bronze within size 1890 X 18053 Head Ceiling Fan – The flush-style ceiling fan is mounted snugly close to a set horizontal fairly low ceiling where it is out of the way, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, depending on the room size being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the instruments and possible other areas essential for installing them, their self-assemble kits have everything else. In many cases, the fan, that may have a unique lighting, will replace a ceiling light fixture.
Safety, The electricity must be off to begin the place that the fan shall be installed. If the fan is replacing a light fixture, power down its fuse or circuit breaker along with flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; tend not to lean or enter a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, as appropriate
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the light fixture in the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws in the electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections for this fixture are cold (quality light will stay off). Cut the wires, leaving 3-5″ of tail allowing you to connect the crooks to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one along with a white one. Tip: also look into the firmness from the electrical box inside the ceiling. If it is not solidly attached to the ceiling, add two extra screws to its top side, which might require drilling two holes inside the box for the kids. The ceiling fan is heavier compared to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires inside the junction box cleanly, install the mounting bracket for the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger into the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor along with a blue or off-color one for your lights being attached below it. Overlap the stripped ends of the two wires (motor and lights) together using the stripped end from the black ceiling wire inside the box, and twist connect them together using the wire nut provided. Connect the white assembly wire for the white ceiling wire much the same way.
Then, to keep these connections from loosening whilst the fan is working, tape the wide lower ends of the nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) for the electrical box if the box can be grounded which has a third bare or green wire. Otherwise, if the electrical box in not grounded, ask a specialist concerning this green wire connection. Some will say to let it sit be, i.e., do nothing at all with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends from the mounting bracket using the small screws provided. It covers/hides the edges from the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets using the screws and washers provided. Then mount the blades for the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to keep them separate in the rest from the kit hardware.
Tip: to keep the motor from becoming too off-level within this step, install the blades one by one opposite to one another to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just below the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided if the lighting assembly is not wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on using the wall switch, whilst the fan itself is controlled through the pull-chain switch only, initially set inside the off position. Note: The ceiling fan includes a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.
