Variable Speed Ceiling Fan – The flush-style ceiling fan is mounted snugly beside a set horizontal fairly low ceiling where it can be off the beaten track, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the room size being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the various tools and possible other regions essential for installing them, their self-assemble kits come with the rest. In many cases, the fan, that will have its own lighting, will replace a ceiling fitting.
Safety, The electricity has to be off at the site where the fan is usually to be installed. If the fan is replacing a fitting, shut down its fuse or circuit breaker in addition to flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; tend not to lean or enter a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring is required, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if necessary
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the fitting through the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws through the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to the fixture are cold (test light will stay off). Cut the wires, leaving 3-5″ of tail in order to connect the crooks to the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one along with a white one. Tip: also check the firmness with the electrical box within the ceiling. If it can be not solidly coupled to the ceiling, add two extra screws to its top side, which might require drilling two holes within the box for them. The ceiling fan is heavier compared to fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires within the junction box cleanly, install the mounting bracket towards the box with the two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger into the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor along with a blue or off-color one for the lights to get attached below it. Overlap the stripped ends of those two wires (motor and lights) together with the stripped end with the black ceiling wire within the box, and twist connect them together with the wire nut provided. Connect the white assembly wire towards the white ceiling wire the same way.
Then, to help keep these connections from loosening as the fan is working, tape the wide lower ends of those nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) towards the electrical box if the box can also be grounded with a third bare or green wire. Otherwise, if the electrical box in not grounded, ask a professional about this green wire connection. Some will say to let it rest be, i.e., do nothing by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends with the mounting bracket with the small screws provided. It covers/hides the perimeters with the motor and the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets with the screws and washers provided. Then mount the blades towards the bottom side of fan motor with the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to help keep them separate through the rest with the kit hardware.
Tip: to help keep the motor from becoming too off-level during this step, install the blades one by one opposite together first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just underneath the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided if the lighting assembly is just not wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on with the wall switch, as the fan itself is controlled with the pull-chain switch only, initially set within the off position. Note: The ceiling fan carries a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.